Chapter 22-11F-2-422) Check if the machine wobbles while it is lying on the desk or the floor,and tighten the adjusting screws if necessary.- When it wobbles in the direction shown by the arrow A, tighten the screwat the right side in the above picture.- When it wobbles in the direction shown by the arrow B, tighten the screwat the left side in the above picture.F-2-433) Mount the cassettes 1 and 2.2.2.5 Connecting the Cable 0007-5059iR2270 / iR2870 / iR3570 / iR4570 / / / /1) If you are installing a cassette pedestal, remove the lattice connectorcover, and fit the lattice connector [1] of the cassette pedestal to themachine.F-2-442) Connect the power plug to the power outlet.1. Power supply voltage shall be +/-10% of the rating.2. The amperage of the power supply must be as rated.3. Before connecting the power plug, check to be sure that the main powerswitch is off.3) Turn on the main power switch.- The machine issues a message to indicate that it is loading programs.- The machine issues a message to indicate that its printer is getting ready fora job.Turning Off the Main PowerWhenever you have to turn off the main power, be sure to go through the fol-lowing to avoid damage to the hard disk:1. Hold down the control panel power switch for 3 sec or more.2. Go through the instructions for the shut-down sequence shown on the dis-play so that the main power switch may be turned off.3. Turn off the main power switch.2.2.6 Connecting the Cable 0010-2913iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N // iR4570N / iR2230 / / iR3530 / / / / /1) If you are installing a cassette pedestal, remove the lattice connectorcover, and fit the lattice connector [1] of the cassette pedestal to themachine.F-2-452) Connect the power plug to the power outlet.1. Power supply voltage shall be +/-10% of the rating.2. The amperage of the power supply must be as rated.3. Before connecting the power plug, check to be sure that the main powerswitch is off.3) Turn on the main power switch.- The machine issues a message to indicate that it is loading programs.- The machine issues a message to indicate that its printer is getting ready fora job.Turning Off the Main PowerWhenever you have to turn off the main power, be sure to go through the fol-lowing to avoid damage to the hard disk:1. Hold down the control panel power switch for 3 sec or more.2. Go through the instructions for the shut-down sequence shown on the dis-play so that the main power switch may be turned off.3. Turn off the main power switch.2.2.7 Stirring Toner 0007-5062iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / iR3530 /1) Enter the Service Mode. (Press "*" first, and "2" and "8" at the same time,and then "*.")2) Select COPIER >FUNCTION > INSTALL> TONER-S.3) Press the OK key.- Toner stirring time is approx. 6 minutes. After counting up, it stopsautomatically.- Make the cassette settings before toner stirring is completed. (See Settingthe Cassettes.)2.2.8 Setting the Cassettes 0007-5065iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / iR3530 /1) Press the cassette release button, and draw out the cassette to the front.2) Check the paper series that the user is going to use, and verify whether ornot the paper series selection switch [1] in the cassette matches that of theuser's selection. If not, change the paper size series to the appropriate one.3) Set the paper size selection dial [2] to the paper size of the paper to beplaced.[A][A][B][B][1][1]
