Chapter 1414-2714.2.6.3 0207 Jam Code: Because solenoid (SL1) of 1st paper delivery flapper is mounted in wrong position. 0010-6523iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / / / iR3530 / / / / /[ Case in the field ]DescriptionIn the field, a sheet of paper dumped into the 1st paper delivery flapper (FL2-1212), causing a paper jam. This was because the solenoid (SL1) of the 1st paperdeliver flapper was positioned higher than usual (i.e., the lower mounting screw was tighten in an upper position of the mounting slot).- 0207 Jam Code: Stationary jam at the fixing/delivery sensor (PS13).Field RemedyWhen the symptom has occurred, follow the procedure below.1. Open the right door, release the 2nd delivery frame assembly, remove the 2 screws from the solenoid cover (FC5-1053), and then detach the cover.2. Loosen the 2 screws that fix the solenoid (SL1), and then tighten the screws again while pushing the solenoid downward.3. Attach the solenoid cover and the 2nd delivery frame, and then close the right door.4. Make copies to make sure that no paper jam occurs.F-14-1914.2.6.4 0B00 Jam Code: Description of this jam code 0010-4115iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /[ Manual-related ]DescriptionThis code can be displayed when the following switch and sensors detect opening of a door during copying or printing.- Door switch (SW2)- Feed cover sensor (PS18)- Front cover sensor (PS22)- Right door open/closed sensor (PS59: on the cassette feeding unit-Y1/Y2)14.2.7 Jam (FIN)14.2.7.1 1205 Jam Code: Finisher-Q3/Saddle Finisher-Q4 0010-5008iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /[ Manual-related ]Description1205 Jam Code means timing jam and can be displayed when the inlet sensor (PI33) detects paper before receiving a delivery signal from the copier.14.2.7.2 1644 Jam Code: Occurs upon power-on or when first paper is fed in punch mode after machine's front cover isopened/closed, Finisher-S1 0010-4114iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /[ Inspected by Canon Inc. ]DescriptionAs a result of inspection, the following was found: The machine with the finisher-S1 causes the symptom when the main power of the machine is turned ONor when the first paper is fed into the machine in the punch mode after the front cover of the machine is opened and closed.- 1644 Jam Code: Punch hole jamField RemedyUpgrade the controller software of the finisher-S1 to version 8.01 or later.14.2.8 Error Code14.2.8.1 E000-0001 Error Code: Because fixing heater is cracked 0009-9813iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 / / / /[ Inspected by Canon Inc. ]DescriptionAs a result of inspection, it was found that the error code was displayed because the fixing heater had been cracked.- E000-0001 can be displayed when the fixing temperature does not reach a given level after a specified period of time has passed.Field RemedyThe conceivable cause of this error code is a fault in the main thermistor or the DC Controller PCB. In the field, however, it occurred because of a crack onthe fixing heater. Therefore, when the error appears, check the fixing heater using a tester. If it has an open-circuit, replace the fixing film unit with a new one.FM2-0358 Fixing Film Unit (for iR2270/2870: 120V)FM2-0359 Fixing Film Unit (for iR2270/2870: 230V)FM2-1793 Fixing Film Unit (for iR3570/4570: 120V)
