Chapter 1515-1715.3.2 Error Codes 0008-0315iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N / / iR4570N / iR2230 / / iR3530 /T-15-9An attempt to connect to the IP address/port in questionfails.1. In user mode, check the TCP/IP settings (gatewayaddress of the IP address settings).2. In user mode, check the LDAP server settings.3. Check to see that the LDAP server is operatingnormally.4. If the login information of the LDAP server is set to'use (security authentication)', check to see if the UDPpacket is blocked by a filter.Check the user name, password, or the settings.If the login information of the LDAP server is set to 'use'or 'use (security authentication)', the user name or thepassword is wrong.In user mode, check the LDAP server settings (username, password).If the login information of the LDAP server is set to 'use(security authentication)', the domain name is wrong.In user mode, check the LDAP server settings (domainname).A timeout condition has occurred, and a search cannot be completed. Check the settings.The search cannot be completed within the specifiedperiod of time.In user mode, increase the length of time before atimeout condition occurs (part of LDAP server settings).An upper limit for search results has been exceeded. If the desired address is not indicated in the results,change the search conditions.The number of matches has exceeded the number ofresults brought up in response to the search.1. Narrow down the search conditions, and try again.2. Try increasing the upper limit.The search conditions include a character that cannot be used for the selected server.The symbol \ is used in the search condition. Remove the symbol \ from the search condition, and tryonce again.The combination of characters used in the searchcondition fails to make up a correct search condition.There must be as many "s as there are "sThe symbol * is not included within parentheses.Check to be sure that the combination of characters is inkeeping with the rule; then, try once again.If LDAP of the server and the character code is version2 (JIS), there is a character that is not part of the ASCIIcode (0x20-0x7E).Remove any character that cannot be used; then, tryonce gain.The version setting of the server is wrong, and the search cannot be initiated. Check the settings.In user mode, the LDAP server settings (server LDAPversion and character code) is set for version 3;however, the LDAP server is operating for version 2.In user mode, set the LDAP server settings so that theLDAP server version and the character code are bothversion 2.Cause Remedy# 001There is a paper or original jam. Remove the jammed paper or original.# 003A communication lasting longer than a specific period oftime (64 min) will cause an error state.1. Decrease the resolution for transmission.2. In the case of reception, ask the source to decrease theresolution or divide the original.# 005The target does not respond within 35 sec. Check to be sure that the target is ready to communicate;then, try once again.The target is a non-G3 model. Check the target.# 009There is no paper. Supply paper.The cassette is not fitted properly. Fit the cassette correctly.# 011The original to be transmitted is not placed properly. Start over from the beginning.# 012The target is out of recording paper, and transmissionhas failed.Ask the target to supply recording paper.# 018There is no response to a redial attempt. Check to make sure that the target is ready forcommunication; then, try once again.The target is engaged for a different communication, andtransmission has failed.Check to make sure that the target is ready forcommunication; then, try once again.The settings do not match the settings of the target, andthe transmission has failed.Check to make sure that the target is ready forcommunication; then, try once again.# 022The particulars of the group address selected as theforwarding target may have been deleted, or there is nomore than a user box, thus causing the transmission tofail.Try transmitting once again.The attempt to transmit to an address registered in theaddress book has failed because the address has beenremoved from the address table while in wait fortransmission.Try once again.Cause Remedy
