|
Chapter 1616-49T-16-6116.7 TEST (Test Print Mode)16.7.1 COPIER16.7.1.1 Copier List 0008-0571iR2270 / iR2870 / iR3570 / iR4570 / / / / / iR2230 / / / iR3530 /T-16-62T-16-631) Press the switch at the operating section long for the shutdown sequence and turn the main power switch OFF.2) Connect the network cable to this machine and turn the main power switch ON.3) Notify the system administrator that the machine has been installed to request network setup.4) Notify the system administrator of the network connection check plan and check the PING remote host address (IP address of a PC terminal in the user network).5) Select the service mode (COPIER>TEST>NETWORK>PING), enter the IP address checked at Step 4 from the ten-key pad of the operating section, and pressthe OK key and the Start key.- Once the network has been connected normally, OK is displayed. (End)- If NG is displayed, check the connection of the network cable first. If the network cable is connected normally, do Step 6 and later. If the network cable is notconnected normally, repeat Step 5.6) Select the service mode (COPIER>TEST>NETWORK>PING), enter the loopback address *(127.0.0.1), and press the OK key and the Start key.- If NG is displayed, the TCP/IP setting of the local machine may be wrong. Return to Step 3 and check the setting again.- If OK is displayed, the TCP/IP setting of the local machine seems correct but the network controller (main controller circuit board) may be faulty. Check thecontroller at Step 7.*: Since the loopback address signal is returned before the network controller, the TCP/IP setting of the local machine can be checked.7) Select the service mode (COPIER>TEST>NETWORK>PING), enter the local host address (IP address of the local machine), and press the OK key.- If NG is displayed, the IP address of the local machine may be wrong or the network controller may be faulty. Check the IP address with the systemadministrator or replace the main controller circuit board.BOARD > OPTIONSub-item Description LevelFONTDL Setting whether or not to display the font service setting screen for listdisplay by the PS kanji font downloader10: Do not display [Default]1: DisplayMENU-1 toMENU-4Setting whether or not to display Levels 1 to 4 of the printer setting menu20: Do not display1: Display[Value at shipping/Value after RAM clearance: 0]COPIER>TEST>PGSub-item Description LevelTYPE Enter a test print type number and press the Start key for test printing. (After testprinting, be sure to return the number to 0.)0: Image from CCD (Ordinary print)1: Checker2: 17 tones (Error diffusion method [T0BIC])3: 17 tones (Dither screen method)4: Totally white 00H5: Halftone 80H (Error diffusion method [T0BIC])6: Halftone 80H (Dither screen method)7: Totally black FFH8: Horizontal line (space: 27 dots, line width: 40 dots)9: Horizontal line (space: 50 dots, line width: 60 dots)10: Horizontal line (space: 3 dots, line width: 2 dots)11: Halftone 60H (Error diffusion method [T0BIC])12: Halftone 60H (Dither screen method)13: Halftone 30H (Error diffusion method [T0BIC])14: Halftone 30H (Dither screen method)15 - 20: For development1TXPH Reserved 1PG-PICK Selecting an output stage for test printing1: Cassette 12: Cassette 23: Cassette 34: Cassette 45: Side deck6: Manual feed7 - 8: Not used12-SIDE Setting the output mode for test printing0: Simplex [Default] 1: Duplex 1PG-QTY Setting the number of pages for test printing1 to 999 [Default: 1] 1COPIER>TEST>NETWORKSub-item Description LevelPING Checking the connection from this machine to the network (TCP/IP only)The network connection is checked when the machine has been installed and when theconnection has become faulty.1
|
