Chapter 1313-3An increase of '1' will decrease the left/right image margin along the frontside by 0.1 mm.F-13-15B-2. 2nd Side of Large-Size Paper (left/right image margin)1) Enter the same ADJ-REFE:COPIER>ADJUST>FEED-ADJ>ADJ-RE-L2) Make a double-sided copy using large-size paper, and check to make surethat the marking is as indicated.3) If not as indicated, change the adjustment value for the 2nd side right/leftimage margin for large-size paper:COPIER>ADJUST>FEED-ADJ>ADJ-RE-LAn increase of '1' will decrease the left/right image margin on the front sideby 0.1 mm.F-13-164) Record the new setting on the service label:- ADJ-REFE- ADJ-RE-L5) Press the Reset key twice to end service mode.13.1.4 Manual Feed Tray 0007-4910iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N // iR4570N / iR2230 / / / iR3530 /A. Adjusting the Left/Right Image Margin (1st side; mechanical)1) Put paper in the manual feed tray.2) Make a copy using the manual feeder as the source of paper, and check tobe sure that the left/right image margin is 2.5 +/-1.5 mm.- If not as indicated, make the following adjustments:3) Remove the paper from the manual feed tray.4) Loosen the fixing screw [1] on the upper over of the manual feed d tray.F-13-175) So that the margin is as indicated, move the top cover of the manual feedtray back and forth.Moving the top cover of the manual feed tray toward the rear of the machinewill decrease the left/right image margin along the front side.6) Tighten fixing screw on the top cover of the manual feed tray.7) Put paper in the manual feed tray.8) Make a copy using the manual feed tray as the source of paper, and checkto make sure that the margin is as indicated.13.1.5 Side Paper Deck 0007-4911iR2270 / iR2870 / iR3570 / iR4570 / / iR2270N / / iR2870N / / iR3570N // iR4570N / iR2230 / / / iR3530 /1) Check to make sure that the 4 adjusters [1] of the pedestal of the hostmachine are in contact with the floor.F-13-182) Connect the power plug of the host machine, and turned on the powerswitch.3) When the host machine has completed its wait period, open the machineusing the paper deck as the source of paper to make sure that the operation isnormal.A. Adjusting the Let/Right Image Margin (1s side; mechanical adjust-ment)1) Make a copy using the paper deck as the source of paper, and check tomake sure that the left/right image margin in the image front direction is 2.5+/-1.5 mm.- If not as indicated, go through the following:2) Slide out the compartment.3) Turn the 2 screws [2] to adjust the mounting position of the latch plate [1]of the deck open solenoid (SL2D) found at the left rear.At this time, use the index [3] of the latch plate as a reference.Paper left edgeIncrease the ADJ-EFE setting.(an increase of '1' willincrease the margin by0.1 mm)Decrease theADJ-REFEsetting.(a decrease of'1' willdecreasethe margin by 0.1 mm)108654202nd side of small-sizedouble-sided copy: 2.5 2.0mmPaper left edgeIncrease theADJ-REF-L setting.(an increase of '1'will decrease themargin by 0.1 mm)Decrease theADJ-REF-L setting.(a decrease of '1'will increase themargin by 0.1 mm)108654202nd side of large-sizedouble-sided copy: 2.5 2.0mm[1][1]
