|
Chapter 1616-47T-16-57Example of display: ST-XXXX 1 ( ) {0 to 0}[1] [2][1] Status display 0: Not installed [Default] 1: Installed[2] Invalidation 0: Invalidate (Only 0 can be entered.)Transfer invalidation procedure1. Select ST-XXXX, enter 0, and press the OK key.2. A transfer license number (24 digits) is displayed at TR-XXXX.T-16-58AP-CODE Setting a CPCA path for a print job from the PrintMe application installed in the PSprint server unit 20 to 99999999 [Default: 0]COPIER >OPTION > COMBOSub-item Description LevelPPR-SLCT SW for the setting of transfer lead edge weak bias (paper type)11: Plain paper (Default), 2: Thick paper, 3: Envelope, 4: Intermediate paper, 5: OHP, 6: Postcard, 7: Labelpaper, 8: Bond paperThe transfer lead edge weak bias becomes effective with the following settings.1.Output condition: Execute 'COPIER>OPTION>COMBO> (1) PPR-SLCT (paper type) / (2) MOD-SLCT(paper pick-up mode) / (3) ENV-SLCT (environment selection)' and register them under TR-SW 1 to 5.2. Execute 'COPIER>ADJUST>HV-TR> (1) TR-TP-TM (length of application time) / (2) TR-TP-LV(application level).'MOD-SLCT SW for the setting of transfer lead edge weak bias (paper pick-up mode)11: One-sided (Default)2: Second side of the paper picked up from a cassette3: Second side of the paper manually fedThe transfer lead edge weak bias becomes effective with the following settings.1. Output condition: Execute 'COPIER>OPTION>COMBO> (1) PPR-SLCT (paper type) / (2) MOD-SLCT(paper pick-up mode) / (3) ENV-SLCT (environment selection)' and register them under TR-SW 1 to 5.2. Execute 'COPIER>ADJUST>HV-TR> (1) TR-TP-TM (length of application time) / (2) TR-TP-LV(application level).'ENV-SLCT SW for the setting of transfer lead edge weak bias (environment selection)11: Low humidity2: Rather low humidity3: Normal humidity (Default: 3)4: Rather high humidity5: High humidityThe setting of '17 becomes valid in all environments only for iR3570/3570F/4570/4570F/iR3530/4530.The transfer lead edge weak bias becomes effective with the following settings.1.Output condition: Execute 'COPIER>OPTION>COMBO> (1) PPR-SLCT (paper type) / (2) MOD-SLCT(paper pick-up mode) / (3) ENV-SLCT (environment selection)' and register them under TR-SW 1 to 5.2.Execute 'COPIER>ADJUST>HV-TR> (1) TR-TP-TM (length of application time) / (2) TR-TP-LV(application level).'TR-SW1/2/3/4/5 SW 1/2/3/4/5 for the setting of transfer lead edge weak bias10: OFF (Default)1: ONRegister the following setting under this switch.COPIER>OPTION>COMBO>PPR-SLCT/MOD-SLCT/ENV-SLCTHow to use this mode1) Set a required combination of the 3 service modes shown above.2) Select any of TR-SW 1 through 5.3) Set the selected switch to '1'.* The transfer lead edge weak bias becomes effective under this condition.** When you select one of TR-SW 1 through 5 while setting any of them to '1', the setting of the selectedswitch is displayed under OPIER>OPTION>COMBO>PPR-SLCT/MOD-SLCT/ENV-SLCT.The transfer lead edge weak bias becomes effective with the settings shown above and below.COPIER>ADJUST>HV-TR (1) TR-TP-TM (length of application time) / (2) TR-TP-LV (application level)COPIER >OPTION >LCNS-TRSub-item Description LevelST-SEND Displaying the send function installation status in transfer invalidation and executingtransfer invalidation 2TR-SEND Acquiring a transfer license key for the send function in transfer invalidation 2COPIER > OPTION > INT-FACESub-item Description Level
|
