Chapter 1818-5Installing the System SoftwareWhen downloaded, the system software is stored in the temporary storage area of the HDD. At the end of downloading, the main power switch must be turned offand then back on, thus restarting the machine and writing the system software to both system area and flash ROM from the temporary storage area. When the mainpower switch is turned off and then back on once again, the machine will start up using the new system software.F-18-318.1.3 Points to Note at Time of Downloading 0011-6811iR7105 / iR7095 / iR7086Do Not Turn Off the Power During Download/Write OperationDo not turn off the power while the system software is being downloaded/written. Otherwise, the machine may fail to start up when its power is turned back on. (Ifsuch is the case, execute HDD formatting, and download the system software. In the case of a boot ROM, replace the DIMM-ROM.)Points to Note About Upgrading the DC Controller/Reader ControllerThe DC controller/reader controller may be downloaded in either in normal mode or in safe mode. If done in safe mode, however, the controller version informationcannot be obtained, causing the data retained by the SST to be written over. It is a good idea, therefore, to use normal mode (so that the software will not be replacedwith software of a previous version).18.2 Making Preparations18.2.1 Installing the System Software (System CD -> SST) 0011-6751iR7105 / iR7095 / iR7086Here, you will be copying the system software found on the System CD to the SST.[Preparatory Work]Requirements- PC to which the SST (version 3.21 or later) has been installed- System CD[Installing the System Software]1) Turn on the PC.2) Set the System CD in the PC.3) Start up the SST.4) Click [Register Firmware].BootROMFLASHROMHDDSystemSoftwareSystemSoftware- - - Do- - - Download Mode - - -wnload Mode - - -[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%[ iR2270i-JPjaxxxx-MN.dsh ] - - - - xx%<<<<< do<<<<< download shell >>>>>wnload shell >>>>>[ SYSTEM JPja-m ] - - - -[ SYSTEM JPja-m ] - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM JPja-w ] - - - -[ SYSTEM JPja-w ] - - - -[ SYSTEM ZZ ] - - - - - - -[ SYSTEM ZZ ] - - - - - - -[ FONT F ] - - - - - - - - - -[ FONT F ] - - - - - - - - - -[ FONT G ] - - - - - - - - - -[ FONT G ] - - - - - - - - - -+++ Switch OFF the po+++ Switch OFF the power then ON.er then ON. ++++++UpgUpgrading completeading completeUpgUpgrading completeading completeUpgUpgrading completeading completeUpgUpgrading completeading completeUpgUpgrading completeading completeUpgUpgrading completeading complete- - - Do- - - Download Mode - - -wnload Mode - - -[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -[ iR2270i-JPjaxxxx-MN.dsh ] - - - - - - - - - -[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -[ iR2270iM-JPjaxxxx-1F77-MN.PRG ] - - - -[ iR2270iM-ZZjaxxxx-49AD[ iR2270iM-ZZjaxxxx-49AD.PRG ] - - - - - - -.PRG ] - - - - - - -[ iR2270iW[ iR2270iW-JPjaxxxx-5C16-MN.PRG ] - - - --JPjaxxxx-5C16-MN.PRG ] - - - -[ iR2270iW[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - --ZZjaxxxx-A825.PRG ] - - - - - - -[ iR2270iF-JPjaxxxx-DE96-ICC[ iR2270iF-JPjaxxxx-DE96-ICC.PRG ] - - - -.PRG ] - - - -[ iR2270iW[ iR2270iW-ZZjaxxxx-A825.PRG ] - - - - - - --ZZjaxxxx-A825.PRG ] - - - - - - -[ iR2270iG-JPjaxxxx-EC30-ICC[ iR2270iG-JPjaxxxx-EC30-ICC.PRG ] - - - -.PRG ] - - - -CompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteCompleteHDDSystemSoftware2)4)5)1)3)Temporarystorage areaSystem areaStatus of reception(sample)The main power switch is turned off and then on.The machine starts up usingthe new version.The main motor switchis turned off and then on.The system software is downloaded.Writing takes place.Temporarystorage area
