Chapter 1616-8E711 An error has occurred in the communication between the pickup/delivery accessory and the printer unit.0001 Indicates the recognition failure of the delivery options on ARCNET network. Turn off and then back on the power. (Turn off the machineand its delivery accessories;then, turn back on all accessories and then the machine.)Connect the communicationcables and terminals between the machine and the deliveryaccessories once again.Replace the accessories controller PCB. Replace thetransceiver PCB.0002 Indicates the optional communication control failure.0003 Indicates no response from the delivery options.E712 An error exists in the communication between the ADF and the reader unit.0001 As much as 5 sec or more has passed without recovery after communicationstoppedbetween the reader controller and the ADF controller.Disconnect and then connect the connectors between thereader unit and the ADF. Replacethe reader controller PCB. Replace the ADF controller PCB.E717 An error exists in the communication with the NE controller.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)0001 The NE controller that has been connected before power-off is not recognizedat power-on.Disconnect and then connect the main controller PCB. Installthe NE controller. Replacethe NE controller.0002 An error that cannot be reset (e.g., cable break) has been detected in thecommunication.E719 An error has occurred in the communication with the coin vendor/card reader.After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)0001 The coin vendor that was connected before power-off is not recognized atpower-on.Disconnect and then connect the connector of the maincontroller PCB. Install the coinvendor. Replace the coin vendor.0002 In the communication with the coin vendor, an error that cannot be reset hasoccurred (e.g.,cable break).0003 In the communication with the coin vendor, a communication error hasoccurred duringacquisition of unit price information.0011 The card reader that was connected before power-off is not recognized atpower-on.Disconnect and then connect the connector of the maincontroller PCB. Install the cardreader. Replace the card reader.0012 In the communication with the card reader, an error that cannot be reset hasoccurred (e.g.,cable break).E730 A PDL-related error has occurred.1001 An initialization error has occurred at the start of a job. Reset the PDL mechanism. Turn off and then on the power.100A An error has occurred in the communication with an external controller.9004 A fault has been detected in the cable connection with an external controller. Turn off and then on the power. Replace the externalcontroller relay PCB. Replace theexternal controller.9005 A fault has been detected in the cable connection with an external controller.A006 The PDL mechanism does not respond. Reset the PDL mechanism. Turn off and then on the power.Reinstall the system software.Replace the main controller.A007 At start-up, the version of the machine control software and that of the PDLcontrolsoftware do not match.Reset the PDL mechanism. Turn off and then on the power.Execute full formatting of theHDD, and reinstall the system software.B013 The font data is corrupted at start-up. Turn off and then on the power. Reinstall the system software.Execute full formatting ofthe HDD, and reinstall the system software.E732 An error has occurred in the communication between the reader unit and the maincontroller.0001 An error has occurred in the communication between the reader unit and themaincontroller.Disconnect and connect the connectors of the readcommunication cable. Check thepower supply of the reader unit (to see if initialization occursat power-on). Replace thereader controller PCB. Reap the reader I/F PCB. Replace themain controller PCB.0010 A fault has been detected in the reader sync signal detection mechanism.E733 An error has occurred in the communication between the reader unit and the maincontroller.0000 An error has occurred in the communication between the reader unit and themaincontroller.Disconnect and then connect the connector. Check the powersupply of the DC controller (tosee if initialization occurs at time of start-up). Replace the DCcontroller PCB. Replace themain controller PCB.0001 An attempt to communicate with the DC controller fails.0010 A fault has occurred in the printer engine sync signal detection mechanism.E740 An error exists in the LAN controller.0002 An illegal MAC address has been detected at start-up. Replace the main controller PCB.E743 A fault exists in the communication between the main controller and the reader controller.0000 The reader controller has detected an error in the communication between themaincontroller and the reader controller.Disconnect and then connect the connectors of the readercommunications cable. Replacethe reader controller PCB. Replace the main controller PCB.E744 An error exists in the language file/boot ROM.Code Description Remedial action*: model equipped with DADF-Q1 (outside Japan, iR7105/7095; inside Japan: iR7105/7095/7086).**: model equipped with DADF-M1 (outside Japan: iR7086).
