BOP-1K 111315 B-29B.104 [SOURce:]VOLTage[:LEVel]:PROTect:POSitive? QUERY VOLT:PROT:POS?Syntax: Short Form: [SOUR:]VOLT[:LEV]:PROT:POS?Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:POSitive?Returns: Description: Identifies the positive protection limit for voltage.B.105 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:BOTH COMMANDVOLT:PROT:LIM[:BOTH]Syntax: Short Form: [SOUR:]VOLT[:LEV]:PROT:LIMit[:BOTH] Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIM[:BOTH where is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) outputvoltage.Description: Establishes the maximum value possible for both the positive and negative protection limits for volt-age. Requires MEM:UPD (PAR. B.12) to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for spe-cial programming considerations.B.106 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]? QUERYVOLT:PROT:LIM[:BOTH]?Syntax: Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM[:BOTH]?Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]?Returns ,Description: Identifies the maximum value possible for protection limits for voltage (positive, negative); maximum is1% greater than rated output voltage.B.107 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative COMMANDVOLT:PROT:LIM:NEGSyntax: Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:NEG Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative where is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) outputvoltage.Description:Establishes the minimum (maximum absolute) value possible for the negative protectionlimit for voltage. This may be set up to 1% greater than rated voltage. Requires MEM:UPD (PAR.B.12) to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for special programming consider-ations.B.108 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative? QUERYVOLT:PROT:LIM:NEG?Syntax: Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:NEG?Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative?Returns: Description:Identifies the minimum (maximum absolute) value possible for the negative protection limitfor voltage.B.109 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive COMMANDVOLT:PROT:LIM:POSSyntax: Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:POS Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:POSitive where is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) outputvoltage.Description:Establishes the maximum value possible for the positive protection limit for voltage. Thismay be set up to 1% greater than rated voltage. Requires MEM:UPD (PAR. B.12) to save for powerup. See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.
