BOP-1K 111315 B-17B.58 [SOURce:]LIST:CURRent:APPLy:SWEep? QUERY LIST:CURR:APPL:SWE?Syntax: Short Form: LIST:CURR:APPL:SWE? Long Form: LIST:CURRent:APPLy:SWEep?Return Value: , (0.01 to 360)Description: Returns start and stop angle in degrees for either triangle and sine wave-forms.B.59 [SOURce:]LIST:CURRent:POINts? QUERY LIST:CURR:POIN?Syntax: Short Form: LIST:CURR:POIN? Long Form: LIST:CURRent:POINts?Return Value: where n = number of pointsDescription: Identifies the total number of points present in a list and the next location to be filled byLIST:CURR command. The LIST:CURR pointer is initially at 0 via LIST:CLE. For each data pointentered by a LIST:CURR command the list pointer is incremented If LIST:CURR:POIN? returns 5, theLIST:CURR pointer is at 5 indicating there are 6 data points comprising the list. If LIST:VOLT has anyentries, an error message: -221,”Settings conflict” is posted in the error queue.Related Commands:LIST:CURR. (See example, Figure B-5.)B.60 [SOURce:]LIST:DWELl COMMAND LIST:DWELSyntax: Short Form: LIST:DWEL (0.000093 to 0.034),,, . . . to maximum of 5900 val-ues.Long Form: LIST:DWELl (0.000093 to 0.034),,, . . . to maximum of 5900 val-ues.Description: Determines how long the main channel parameters will be active. Sets time value (from 0.000093to 0.034) in Seconds for List:Dwell locations illustrated in Table B-2. These locations are associatedwith the corresponding main channel locations illustrated in Table B-2. The main channel is deter-mined by FUNC:MODE, either current (FUNC:MODE CURR) or voltage (FUNC:MODE VOLT) IfLIST:DWEL is entered for only location 0, that time duration will apply to all steps when eitherVOLT:MODE LIST or CURR:MODE LIST is executed. Related Commands: VOLT:MODE,FUNC:MODE, LIST:CURR, LIST:VOLT, LIST:DWEL?. (See example, Figure B-5.)B.61 [SOURce:]LIST:DWELl? QUERY LIST:DWEL?Syntax: Short Form: LIST:DWEL? Long Form: LIST:DWELl?Return Value: Description: Identifies the dwell times entered for the list. Starting at location established by LIST:QUERy,returns comma-separated list of up to 16 values indicating the dwell time parameters entered. i.e., thecontents of LIST:DWEL locations of Table B-2. Related Commands: LIST: DWEL, LIST:QUERy. (Seeexample, Figure B-5.)B.62 [SOURce:]LIST:DWELl:POINts? QUERY LIST:DWEL:POIN?Syntax: Short Form: LIST:DWEL:POIN? Long Form: LIST:DWELl:POINts?Return Value: (0 to 5900)Description:Identifies the number of locations for which time values have been entered and the next loca-tion to be filled by a LIST:DWEL command. If LIST:DWEL:POIN? returns 6, dwell times have beenentered for locations 0 through 5 and location 6 is the next to be filled by a LIST:DWEL command.LIST:DWEL, LIST:DWEL:POIN. (See example, Figure B-5.)B.63 [SOURce:]LIST:QUERy COMMAND LIST:QUERSyntax: Short Form: LIST:QUER Long Form: LIST:QUERy int_value = where n = first location to be queried.Description: Determines first location to be queried by LIST:VOLT?, LIST:CURR? or LIST:DWEL? queries.Related Commands: LIST:VOLT?, LIST:CURR?, LIST:DWEL?. LIST:QUER?. (See example, Figure B-5.)B.64 [SOURce:]LIST:QUERy? QUERY LIST:QUER?Syntax: Short Form: LIST:QUER? Long Form: LIST:QUERy?Return Value: Description: Identifies first location to be queried by LIST:VOLT?, LIST:CURR?, LIST:DWEL? queries.Related Commands: LIST:QUER, LIST:CURR?, LIST:DWEL?. LIST:QUER?. (See example, Figure B-5.)
