Chapter 1515-2915.5 Alarm Codes15.5.1 Alarm Code 0014-0594imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / imagePRESS C1+T-15-120093 User cover open PI3,PI6 When opening of a cover (front or rear) is detected while the machine is in operation.0094 Initial stationary PI4,PI12,PI13,S1,S2,S3,S4,S5,S9When a sensor in the delivery path detects a document when the operation is started.0095 Cycle NG S6 When a pickup signal is received for a specified period of time (2 sec) in the no document detection state.0096 Remaining document S1 When the reverse sensor detects a document while the belt motor is driven by a specified amount beforea left pickup job is started.0097 Manual feed documentstationaryS1,S9 When the reverse sensor detects a document while the mulfifeed registration roller sensor is detecting itduring the multifeed pickup operation.0098 Power down - When supply voltage from the main unit is lowered while the machine is in operation.Block Code Detailed Code01 main body (general) 0000 Indicates the presence of 11 pixel or larger dust (Red)0001 Indicates the presence of 11 pixel or larger dust (Green)0002 Indicates the presence of 11 pixel or larger dust (Blue)02 scanning system 0000 Indicates the presence of dust on all the lines of sub scanner (at the end of job)0001 Indicates the presence of dust on all the lines of sub scanner (at the beginning of job)04 pickup / feeding system 0000 Indicates that the fan lock signal does not change to LOW even 2 sec after fan starts driving0008 Indicates the accessory deck lifter error0011 Indicates the cassette 1 retry pickup error0012 Indicates the cassette 2 retry pickup error0013 Indicates the cassette 3 retry pickup error0014 Indicates the cassette 4 retry pickup error0017 Indicates the MPtray retry pickup error0018 Indicates the otion deck retry pickup error0031 Indicates the cassette 1 lifter motor overcurrent0032 Indicates the cassette 2 lifter motor overcurrent0033 Indicates the cassette 3 lifter motor overcurrent0034 Indicates the cassette 4 lifter motor overcurrent06 fixing system 0002 Indicates that the fixing upper roller life is over0003 Indicates the no fixing web10 Developing System, Copier 0001 Toner low (Bk)(This alarm code issued by RDS.)0002 Toner low (C)(This alarm code issued by RDS.)0003 Toner low (M)(This alarm code issued by RDS.)0004 Toner low (Y)(This alarm code issued by RDS.)0005 * Toner low (L)(This alarm code issued by RDS.)11 waste toner collecting system 0001 Indicates that the waste toner is full33 fan 0014 Indicates the feeding fan 1 alarm0015 Indicates the feeding fan 2 alarm61 finisher 0001 Indicates the absence of staple62 saddle stitcher 0001 Indicates the absence of stitch65 puncher 0001 Indicates that the punch chips are full72 Surf 0001 Indicates the faulty access to the register0002 Indicates the faulty data transmission to the memory (includes timeout)0003 Indicates the rendering error (ECI module)0004 Indicates the rendering error (EM module)0005 Indicates the rendering error (IE module)0006 Indicates the rendering error (IDM module)0007 Indicates the rendering error (LAM module)0008 Indicates the rendering error (MI module)0009 Indicates the rendering error (PCM module)0010 Indicates the rendering error (PGM module)0011 Indicates the rendering error (VII module)0012 Indicates the rendering error (VOI module)0014 Indicates the rendering error (rendering timeout)0015 Indicates the rendering error (MRA module)0016 Indicates the rendering error (POC module)Code Type of Jam Sensor No. Details
