Chapter 1313-1113.5.4 After Replacing the HDD 0014-3735imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1. If NSA (Net Spot Account) is not used:1) Formatting the HDDStart the equipment to the SafeMode (turn on the main power pressing2+8 key).Using the HD formatting function of the SST, format all the partitions.(See the chapter on version upgrade for more details.)2) Downloading the system softwareUse SST to download system / Language / RUI. It can take about 5minutes to restart after downloading.2. If NSA (Net Spot Account) along with card reader is used:A card ID for NSA is downloaded on the HDD. When replacing the HDD,card data must be downloaded from the NSA again so that counting manage-ment is possible in the NSA.[Just as is in the case where NSA is not used (1.), after formatting the HDDand downloading the system software different procedure must be followed.1) HDD FormattingStart the equipment to the SafeMode (turn on the main power pressing2+8 key).Using the HD formatting function of the SST, format all the partitions.(See the chapter on version upgrade for more details.)2) Downloading the System SoftwareUse SST to download system / Language / RUI. It can take about 5minutes to restart after downloading.3) In the Service ModeSelect: COPIER > FUNCTION > INSTALL > CARD.4) Entering the Card NumberEnter the number of the first card of the cards used in divisionalmanagement, and then press Enter. (E.g. If using cards numbered 1 to1000 for divisional management, enter the first card's number, "1".)5) Turn off the main power and then turn it back on.6) Confirming the Count ManagementIn the User Mode, select "System Management Setup > Group IDManagement > Count Management" and confirm ID's numbered fromID00000001 to ID00001000 have been created.7) Setting Up AddressesIn the User Mode, select "System Management Setup > Net WorkSettings > TCP IP Setup > IP address" and set up IP address, gatewayaddress, and subnet mask.8) Entering ID'sIn "System Administrator Information Setup" in the User Mode, register"System Management Group ID" and "System Management ID."9) Turn off the main power and then turn it back on.If the "System Management Group ID" and "System Management ID" is notregistered, "Card Registration to the Device" cannot be done when settingNet Spot Accnout.10) Downloading Card IDWhile putting the equipment on stand-by, download card ID from theNSA to be used for the repaired equipment.11) Confirmation of Count ManagementIn the User System select: System Management Setup > Group ID Setup> Count Management." Confirm that only ID's that have beendownloaded are displayed.12) Confirmation of PerformanceTry photocopying a document using the User Card registered at the NSA,and confirm the card is counted in the counting device of the NSA.13.5.5 Replacing the HV2, HV4, HV6-1 and HV6-2 0014-3049imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Execute the service mode (high-voltage offset adjustment: COPIER >FUNCTION > MISC-P > HV-ADOFS).On execution of this service mode, the waste toner sensor offset adjustmentis executed. If toner is left inside the waste toner bottle here, toner adjustmentcannot be carried out properly, resulting in an error code in some cases(E0013-0006: waste toner sensor adjustment error). Be sure to execute thisservice mode after removing the waste toner bottle from the main body.13.5.6 Inputting the Rank Value at Replacing the PaperThickness Sensor 0013-3425imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+Input the values corresponding to the characters on the label attached to thenew paper thickness sensor in the following service mode items.- COPIER > ADJUST > MISC > DF-S-NK (Inputting the rank values for thepaper thickness sensor.)13.6 Pickup/Feeding System13.6.1 Vertical Registration Adjustment at CassettePickup 0013-3422imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+Copy from each cassette, check if the left/right image margin are within thestandards.When the value is not within the standard value, adjust it by the followingprocedures.1) Press the set release button, pull the cassette forward.2) Open the right upper cover and right lower cover.3) Insert the driver from the hole of the right front crossmember, loosen thescrew [1] and adjust the location of the adjusting plate [2].F-13-32Move the adjusting plate to the rear side: The left margin decreases.Move the adjusting plate to the front side: The left margin increases.4) Hold the screw.5) Close the right cover (upper) and right cover (lower).6) Mount the cassette.13.6.2 Vertical Registration Adjustment at Manual Pickup0013-3423imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+Copy from the manual tray, check if the left/right image margin are withinthe standards.When the value is not within the standard value, adjust it by the followingprocedures.1) Loosen one screw [1], move the fixing location of the slide guide [2] toadjust the vertical registration.Character on the label DF-S-NK input valueA 1B 2C 3D 4E 5[1][2]
