Chapter 99-49Points to Note when Attaching the Refresh Roller Unit- Be sure to attach the refresh roller after removing the protection sheet. Theprotection sheet cannot be removed after attaching the refresh roller.- Be sure to spread a sheet [3] beneath the fixing roller so as not to damageit. After attaching the refresh roller unit, draw the sheet [3] out.8) Remove the refresh roller [1].- 2 E-rings [2]- 1 gear [3]- 3 bearings [4]- 1 spring [5]- 1 spacer [6]- 2 bushings [7]F-9-1199.7.11 Steering Roller9.7.11.1 Preparation for Removing the Steering Roller 0014-0224imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Open the front door.2) Pull out the fixing/feeding unit toward you.3) Remove the fixing belt unit. (page 9-38)Reference [Removing the Fix-ing Belt Unit]4) Remove the fixing belt. (page 9-42)Reference [Removing the FixingBelt]9.7.11.2 Removing the Steering Roller 0014-0225imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Remove the steering roller [1].- 4 E-rings [2]- 2 gears [3]- 1 dowel pin [4]- 4 bearings [5]- 2 spacers [6]F-9-1209.7.12 Pressure Pad9.7.12.1 Preparation for Removing the Pressure Pad 0014-0180imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Open the front door.2) Pull out the fixing/feeding unit toward you.3) Remove the fixing belt unit. (page 9-38)Reference [Removing the Fix-ing Belt Unit]4) Remove the fixing belt. (page 9-42)Reference [Removing the FixingBelt]5) Remove the oil coating roller. (page 9-44)Reference [Removing the OilCoating Roller]6) Remove the pressure pad cover. (page 9-49)Reference [Removing thePressure Pad Cover]9.7.12.2 Removing the Pressure Pad 0014-0181imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Remove the pressure pad [1].- 2 screws [2]F-9-1212) Detach the stopper plate [2] from the pressure pad [1].F-9-1229.7.13 Pressure Pad Cover9.7.13.1 Preparation for Removing the Pressure PadCover 0014-0178imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Open the front door.2) Pull out the fixing/feeding unit toward you.3) Remove the fixing belt unit. (page 9-38)Reference [Removing the Fix-ing Belt Unit]4) Remove the fixing belt. (page 9-42)Reference [Removing the FixingBelt]5) Remove the oil coating roller. (page 9-44)Reference [Removing the OilCoating Roller]9.7.13.2 Removing the Pressure Pad Cover 0014-0179imagePRESS C1 P / imagePRESS C1 / imagePRESS C1+ (Printer) / image-PRESS C1+1) Remove the pressure pad cover support [1].- 2 E-rings [2]- 1 gear [3]- 1 dowel pin [4]- 2 bearings [5]- 1 spacer [6]- 6 screws [7][1][4][7][2] [3][4][4] [6][7][5][2][1][2][2][2][2] [3][3]MEMO:When replacing the pressure pad, detach the stopper plate [2] from thepressure pad [1]. If the stopper plate [2] cannot be detached, replacethe stopper plate (FC7-1842).[1][2][2][1][2]
