Toshiba GR200 Series Instruction Manual

Also see for GRB200: Instruction manual

6F2S1931 (0.20)Centralized GRB200(Soft: 030, 031, 032, 033, 034)- 313 -Table 4.6-6 Settings of LEDs on the Function keys (Function ID: 240001)Setting items Range Units Contents Default settingvalueF1Input signal1 (Preferred Data ID) - Set a Data ID at the first input on F1 (No Assigned)Input signal2 (Preferred Data ID) - Set a Data ID at the second input on F1. (No Assigned)Input signal3 (Preferred Data ID) - Set a Data ID at the third input on F1. (No Assigned)Input signal4 (Preferred Data ID) - Set a Data ID at the forth input on F1. (No Assigned)Input signal5 (Preferred Data ID) - Set a Data ID at the fifth input on F1. (No Assigned)Input signal6 (Preferred Data ID) - Set a Data ID at the sixth input on F1. (No Assigned)Input signal7 (Preferred Data ID) - Set a Data ID at the seventh input on F1. (No Assigned)Input signal8 (Preferred Data ID) - Set a Data ID at the eighth input on F1. (No Assigned)Reset signal (Preferred Data ID) - Setting Data ID for "Latch" circuit (No Assigned)LOGIC-SW AND / OR / XOR - Switch for logic-gate operation on F1 ANDINVERSE-SW Normal / Inverse - Inversion operation of F1 signal NormalTIMER-SW Off/Delay/Dwell/Latch/Blink - Selection of a type in the delay timer on F1 OffOn Delay Timer 0.00 – 300.00 s Set a value for an on-delay-timer on F1 0.00Off Delay Timer 0.00 – 300.00 s Set a value for an off-delay-timer on F1 0.00Logic Timer 0.00 – 300.00 s Off delay timer value for "Delay" and "Dwell" circuit 0.00F2Input signal1 (Preferred Data ID) - Set a Data ID at the first input on F2 (No Assigned)Input signal2 (Preferred Data ID) - Set a Data ID at the second input on F2. (No Assigned)Input signal3 (Preferred Data ID) - Set a Data ID at the third input on F2. (No Assigned)Input signal4 (Preferred Data ID) - Set a Data ID at the forth input on F2. (No Assigned)Input signal5 (Preferred Data ID) - Set a Data ID at the fifth input on F2. (No Assigned)Input signal6 (Preferred Data ID) - Set a Data ID at the sixth input on F2. (No Assigned)Input signal7 (Preferred Data ID) - Set a Data ID at the seventh input on F2. (No Assigned)Input signal8 (Preferred Data ID) - Set a Data ID at the eighth input on F2. (No Assigned)Reset signal (Preferred Data ID) - Setting Data ID for "Latch" circuit (No Assigned)LOGIC-SW AND / OR / XOR - Switch for logic-gate operation on F2 ANDINVERSE-SW Normal / Inverse - Inversion operation of F2 signal NormalTIMER-SW Off/Delay/Dwell/Latch/Blink - Selection of a type in the delay timer on F2 OffOn Delay Timer 0.00 – 300.00 s Set a value for an on-delay-timer on F2 0.00Off Delay Timer 0.00 – 300.00 s Set a value for an off-delay-timer on F2 0.00Logic Timer 0.00 – 300.00 s Off delay timer value for "Delay" and "Dwell" circuit 0.00……….F7Input signal1 (Preferred Data ID) - Set a Data ID at the first input on F7 (No Assigned)Input signal2 (Preferred Data ID) - Set a Data ID at the second input on F7. (No Assigned)Input signal3 (Preferred Data ID) - Set a Data ID at the third input on F7. (No Assigned)Input signal4 (Preferred Data ID) - Set a Data ID at the forth input on F7. (No Assigned)Input signal5 (Preferred Data ID) - Set a Data ID at the fifth input on F7. (No Assigned)Input signal6 (Preferred Data ID) - Set a Data ID at the sixth input on F7. (No Assigned)Input signal7 (Preferred Data ID) - Set a Data ID at the seventh input on F7. (No Assigned)Input signal8 (Preferred Data ID) - Set a Data ID at the eighth input on F7. (No Assigned)Reset signal (Preferred Data ID) - Setting Data ID for "Latch" circuit (No Assigned)LOGIC-SW AND / OR / XOR - Switch for logic-gate operation on F7 ANDINVERSE-SW Normal / Inverse - Inversion operation of F7 signal NormalTIMER-SW Off/Delay/Dwell/Latch/Blink - Selection of a type in the delay timer on F7 OffOn Delay Timer 0.00 – 300.00 s Set a value for an on-delay-timer on F7 0.00Off Delay Timer 0.00 – 300.00 s Set a value for an off-delay-timer on F7 0.00Logic Timer 0.00 – 300.00 s Off delay timer value for "Delay" and "Dwell" circuit 0.00