– 114 –Chapter 6 Input/Output Signal Settings — Setting MultiView displaysSetting MultiView displaysThe unit has 4 lines of MultiView display that can be split up to 16 screens.Setting the screen layoutIn [Split] of the [Pattern] column, select a split-screen layout from the following 9 options.43212153 42153 42163 4 525 613 47 8 94 5 61 2 317 8 9 103 4 5 6213 4 5 67 8 9 1021 2 3 45 6 7 89 10 11 1213 14 15 16[4Split][5-aSplit][5-bSplit][6-aSplit][6-bSplit] [9Split][10-aSplit][16Split][10-bSplit]1 Select the button → [MV1‑4] → [MV1] to [MV4] tabs.2 Select an item in [Split] in the [Pattern] column.f Select the split-screen layout.3 Select an item in [Size] in the [Pattern] column.f Set the size mode of the split screens.f This function will be available in V2.00.00 or higher.[Fit] The size of the split frame is the same as the split-screen size.[SQ] The split-screen size is smaller than the split-frame size, and the source names, level meter, etc. are displayed outsidethe split screen.4 Select an item in [Assign] in the [Pattern] column.f The assign setting screen for the sub-screen is displayed.f Signals that can be assigned: SDI IN1 to SDI IN32, DVI IN1 to DVI IN2, Still 1V to Still 4V, Still 1K to Still 4K, Clip 1V to Clip 4V, Clip 1K to Clip4K, CBAR, Black, CBGD1, CBGD2, ME1PGM, ME1PVW, ME1CLN, ME1KEYPVW, ME2PGM, ME2PVW, ME2CLN, ME2KEYPVW, DSKPGM1,DSKPGM2, DSKPVW1, DSKPVW2, DSK1CLN to DSK4CLN, SEL KEYPVW, MV1 to MV4, AUX1 to AUX16, Clock, LTC@@ NOTEt When an input signal (SDI IN1 to SDI IN32, DVI IN1 to DVI IN2, Still 1V to Still 4V, Still 1K to Still 4K, Clip 1V to Clip 4V, Clip 1K to Clip 4K, CBAR,Black, CBGD1, CBGD2) is selected, the source name set from the button → [SOURCE NAME] → [Panel Name]/[MV Name] tab is displayed.If the input signal is selected in the AUX bus (AUX1 to AUX16), the first 4 letters of the source name are displayed in [ ].- When SDI IN1 (source name: CAM1) is selected in AUX1: AUX1[CAM1]- When SDI IN2 (source name: CAMERA2) is selected in AUX2: AUX2[CAME]t When MV1 to MV4 are displayed on the sub-screen of the MultiView display, the images are looped as if two mirrors were facing each other.Setting the split frame and charactersSet the frame, character luminance, and background of the split screens to be displayed on the MultiView display.1 Select the button → [MV1‑4] → [MV1] to [MV4] tabs.2 Select an item in [Frame] in the [MV Frame] column.f Set the luminance and display of the split frames.Select from [Off], [LUM 0%], [LUM 25%], [LUM 50%], [LUM 75%], and [LUM 100%].3 Select an item in [Character] in the [MV Frame] column.f Set the luminance and display of the characters.Select from [Off], [LUM 0%], [LUM 25%], [LUM 50%], [LUM 75%], and [LUM 100%]. When [Off] is selected, the character background is notdisplayed.4 Select an item in [Label] in the [MV Frame] column.[On] Displays the character background (half-tone).[Off] Does not display the character background (half-tone).Setting the tally displayConfigure the tally display setting to be superimposed onto the split frame of the MultiView display.
