– 74 –Chapter 5 Basic Operations — Color correctorColor correctorThe unit can correct the colors of video signals because its terminals to , and to are equippedwith the color corrector function.@@ NOTEt This function will be available in V2.00.00 or higher.Setting the color corrector1 Select the button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.2 Select an item in [Enable] in the [Operation] column.[On] Enables the color corrector of the relevant channel.[Off] Disables the color corrector.3 Select an item in [Limit] in the [Operation] column.[Off] Does not restrict the color range of input signals.[108] Restricts the amplitude level of the colors (R, G, and B) to 0% to 108%.[104] Restricts the amplitude level of the colors (R, G, and B) to 0% to 104%.[100] Restricts the amplitude level of the colors (R, G, and B) to 0% to 100%.Initializing the color corrector1 Select the button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.2 Select an item in [Initialize] in the [Operation] column.[Process] Initializes the setting value in the [Process] column.[Tone] Initializes the setting values in the [Tone1 Black]/[Tone2 Gray L]/[Tone3 Gray H]/[Tone4 White] column.[RGB Matrix] Initializes the setting values in the [Matrix R/G]/[Matrix B] column.[Axis Matrix] Initializes the setting values in the [CC B-Mg/Mg]/[CC Mg-R/R]/[CC R-Ye/Ye]/[CC Ye-G/G]/[CC G-Cy/Cy]/[CC Cy-B/B]column.[All] Initializes all.Copying the setting1 Select the button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.2 Select an item in [Copy From] in the [Operation] column.f The setting of the selected tab is copied. However, the setting of the [Operation] column is not copied.Process control1 Select the button → [C/C IN 25‑30], [C/C IN 31‑32], [C/C OUT] → the tab to be set.f Select the tab to be set from the [SDI IN 25] tab to [SDI IN 32] tab, or the [SDI OUT 13] tab to [SDI OUT 16] tab.2 Set [Y‑Gain], [Pedestal], [C‑Gain], and [Hue] in the [Process] column.[Y‑Gain] Sets the gain value of the Y signal.[Pedestal] Sets the value of the pedestal level (black level).[C‑Gain] Sets the gain value of the saturation (Sat).[Hue] Sets the amount of change of the hue (Hue).3 Select an item in [Colorimetry] in the [Process] column.f Set the colorimetry conversion for SD/HD conversion.[On]Converts the SD format to the HD format.f To enable this item, set the system to HD mode, and set the button on the top menu → [SDI IN] → [FrameBuffer] tab → [Mode] in the [SDI IN 1] to [SDI IN 32] columns to [Dot by Dot] or [U/C].[Off] Does not perform conversion.
