– 153 –Chapter 10 Specifications — SpecificationsSpecificationsMain Frame AV‑HS60U1/AV‑HS60U2Power supplyAC 100 V to 240 V, 50 Hz/60 HzPower consumption110 WAV-HS60U2 supports redundant power supply.indicates safety information.Video terminal to terminals 32 linesf Connectors: BNC×32f , , , and terminals are equipped with up-converters.f to terminals are equipped with color correctors.HD-SDI HD serial digital, SMPTE292M (BTA S-004) standard compliantf 0.8 V [p-p] ±10% (75 Ω)f Automatic equalizer 100 m (328 ft) (when 1.5 Gbps/5C-FB cable is used)SD-SDI SD serial digital, SMPTE259M standard compliantf 0.8 V [p-p] ±10% (75 Ω)f Automatic equalizer 200 m (656 ft) (when 5C-2V cable is used)/ terminals 2 linesDigital RGB: XGA (1024×768), WXGA (1280×768), SXGA (1280×1024), WSXGA+ (1680×1050), UXGA (1600×1200),WUXGA (1920×1200)Vertical frequency: 60 HzVideo format inputs: 1080/50p, 1080/59.94p, 1080/50i, 1080/59.94i, 720/50p, 720/59.94pf Connectors: DVI-D×2f The terminals do not support HDCP.f The DVI-I connector cable cannot be used.f For the DVI-D connector cable, use a cable with a length of up to 5 m (16.4 ft). to terminals16 lines (2 distribute outputs per line)f Connectors: BNC×32f ME1PGM, ME1PVW, ME1CLN, ME1KEYPVW, ME2PGM, ME2PVW, ME2CLN, ME2KEYPVW, DSKPGM1, DSKPGM2,DSKPVW1, DSKPVW2, DSK1CLN, DSK2CLN, DSK3CLN, DSK4CLN, SEL KEYPVW, MV1 to MV4, and AUX1 toAUX16 can be assigned.HD-SDI HD serial digital, SMPTE292M (BTA S-004) standard compliantf Output level: 0.8 V [p-p] ±10%f Rise time: Less than 270 ps (HD)f Fall time: Less than 270 ps (HD)f Difference between rise time and fall time: 100 ps or less (HD)f Alignment jitter: 0.2 UI (130 ps) or less (HD)f Timing jitter: 1.0 UI or less (HD)f Eye aperture ratio: 90% or moref DC offset: 0±0.5 VSD-SDI SD serial digital, SMPTE259M standard compliantf Output level: 0.8 V [p-p] ±10%f Rise time: 1.5 ns or lessf Fall time: 1.5 ns or lessf Difference between rise time and fall time: 0.5 ns or lessf Jitter: 0.2 UI or lessSignal formats SD 480/59.94i, 576/50iHD 1080/59.94i, 1080/50i, 720/59.94p*, 720/50p*, 1080/24PsF*, 1080/23.98PsF*Signal processing Y:PB:PR 4:2:2 10 bitsR:G:B 4:4:4 8 bitsME number 2ME* 720/59.94p, 720/50p, 1080/24PsF, and 1080/23.98PsF will be available in V2.00.00 or higher.Synchronous terminal[ terminal] In Genlock mode: Black burst or Tri-level Sync input signals (with loop-through)f If the loop-through output is not used, provide a 75 Ω termination.In internal sync mode: Black burst output signal ×2f Connector: BNCf Same field frequencies as those of the system formats supportedf In the 1080/24PsF and 1080/23.98PsF formats, only Genlock mode supportedf In the 1080/23.98PsF format, black burst signals with 10 Field ID (SMPTE318M standard compliant) or Tri-level Syncsignals supported
