Panasonic AV-HS6000 Operating Manual

Also see for AV-HS6000: Operation guide Firmware upgrade guide

Contents

Panasonic AV-HS6000 Operating Manual Manual pdf 130 page image

– 130 –Chapter 8 System Menu — System settings[1F Fix]The video is delayed by one frame (1F).f The delay difference during transition (when [SQ], [SL], or [3D] is selected in the wipe pattern) and after transition willdisappear.r Setting the delay amountItem After transition MIX/WIPE SQ/SL/3D/Flying Key*[Minimum] No delay No delay 1F delay[1F Fix] 1F delay 1F delay 1F delay* The flying key is a [Key]‑only setting.Setting the SDI signal ancillaryThis setting enables a function that allows V ancillary data and embedded audio data of an SDI input signal to pass through.f HD format: Ancillary data starting with line 9 is allowed to pass through.f SD format: Ancillary data starting with line 12 is allowed to pass through.When 1080/59.94i, 720/59.94p, 1080/50i, or 720/50p is selected as the system format of the unit, it is not possible to allow the ancillary data andembedded audio data to pass through even if SD format signals (480/59.94i or 576/50i) have been input in the [Dot by Dot] mode or [U/C] mode.For details, refer to “Setting the input mode” (page 106).1 Select the button → [SYSTEM] → [Video] tab.2 Select an item in [AUX] in the [Ancillary] column.[Off] The ancillary data and embedded audio data are not allowed to pass through on AUX1 to AUX16 outputs.[On] The ancillary data and embedded audio data of the SDI input sources selected by the AUX bus (AUX1 to AUX16) areallowed to pass through.3 Select an item in [PGM] in the [Ancillary] column.[Off] The ancillary data and embedded audio data are not allowed to pass through on ME1PGM, ME2PGM, DSKPGM1, andDSKPGM2 outputs.[On] The ancillary data and embedded audio data of the SDI input sources selected by the PGM bus are allowed to passthrough.4 Select an item in [PVW] in the [Ancillary] column.[Off] The ancillary data and embedded audio data are not allowed to pass through on ME1PVW, ME2PVW, DSKPVW1, andDSKPVW2 outputs.[On] The ancillary data and embedded audio data of the SDI input sources selected by the PST bus are allowed to passthrough.Setting the ancillary for the MultiView display1 Select the button → [SYSTEM] → [Video] tab.2 Select an item in [MV1] to [MV4] in the [MV Ancillary] column.f Select the bus that will superimpose ancillary data and embedded audio data on each MultiView display.[ME1‑PGM]/[ME2‑PGM] The ancillary data and embedded audio data of the SDI input sources selected by the [ME1-PGM]/[ME2-PGM] bus areallowed to pass through.[ME1‑PVW]/[ME2‑PVW] The ancillary data and embedded audio data of the SDI input sources selected by the [ME1-PVW]/[ME2-PVW] bus areallowed to pass through.[DSK‑PGM] The ancillary data and embedded audio data of the SDI input sources selected by the [ME1-PGM]/[ME2-PGM] bus priorto DSK are allowed to pass through.[Off] Not allowed to pass through.Setting the crosspoint switchingThe timing at which the crosspoints are to be switched can be set.f This switching involves the operation of the crosspoint buttons and the button.1 Select the button → [SYSTEM] → [Video] tab.2 Select an item in [Timing] in the [XPT Switch] column.f Select the timing of switching.[Any] The crosspoints are switched in the nearest field. This is for live applications.[Field1] The crosspoints are switched in field 1. This is for editing applications.[Field2] The crosspoints are switched in field 2. This is for editing applications.Network settingsFor details on network settings, refer to “Network settings” (page 42).