Panasonic AV-HS6000 Operating Manual

Also see for AV-HS6000: Operation guide Firmware upgrade guide

Contents

Panasonic AV-HS6000 Operating Manual Manual pdf 112 page image

– 112 –Chapter 6 Input/Output Signal Settings — Setting output signalsSetting output signals[SDI OUT 1] to [SDI OUT 16] are used for SDI signal output.The functions differ depending on the output signals.@@ NOTEt 1080/24PsF, 1080/23.98PsF, 720/59.94p, and 720/50p will be available in V2.00.00 or higher.r List of settings by output signalf “l” indicates enabled, and “―” indicates disabled.[Assign] Color corrector* [Down Converter][SDI OUT 1] - [SDI OUT 12] l ― ―[SDI OUT 13], [SDI OUT 15] l l ―[SDI OUT 14], [SDI OUT 16] l l l* This function will be available in V2.00.00 or higher.For details, refer to “Color corrector” (page 74).Assigning output signalsAssign output signals to [SDI OUT 1] through [SDI OUT 16].1 Select the button → [SDI OUT] → [Assign] tab.2 Set the output signals to assign.f Output signals that can be assigned are as follows.ME1PGM, ME2PGM, DSKPGM1,DSKPGM2Outputs an image with the wipe, mix, key, downstream key or other effect to the switcher's main line output.DSKPVW1, DSKPVW2 Outputs the DSK preview signal with the ME1PVW or ME2PVW output signal in background.AUX1 ‑ AUX16 Outputs the signal selected by the 16 lines of AUX buses ([AUX1] to [AUX16]).ME1CLN, ME2CLN, DSK1CLN,DSK2CLN, DSK3CLN, DSK4CLNOutputs clean signals before key effects were added. ME1CLN and ME2CLN signals can be switched to the Key Outsignals which are used for key combination.MV1 ‑ MV4 Outputs the MultiView display signal. Multiple input and output signals are reduced and output to a single screen.(page 114)ME1KEYPVW, ME2KEYPVW,SEL KEYPVWOutputs the preview signal exclusively for the key.ME1PVW, ME2PVW Outputs the preview signals for BKGD, KEY1 to KEY4 which were selected in the next transition.f For details on ME/DSK output signal settings, refer to “Setting the ME output and DSK output” (page 132).Setting the down‑converterFor [SDI OUT 14], [SDI OUT 16], the down-converter is available.When the system format is 1080/59.94i, 720/59.94p, the image is output in 480/59.94i format.When the system format is 1080/50i, 720/50p, the image is output in 576/50i format.This function cannot be selected when the system format is SD (480/59.94i, 576/50i).1 Select the button → [SDI OUT] → [Down Converter] tab.2 Select an item in [Enable] in the [SDI OUT 14]/[SDI OUT 16] column.[Off] Disables the down-converter.[On] Enables the down-converter.3 Select an item in [Limit] in the [SDI OUT 14]/[SDI OUT 16] column.f Set the color range.[Off] Does not restrict the color range.[108%] Restricts the amplitude level of the colors (R, G, and B) to 0% to 108%.[104%] Restricts the amplitude level of the colors (R, G, and B) to 0% to 104%.[100%] Restricts the amplitude level of the colors (R, G, and B) to 0% to 100%.4 Select an item in [Scale] in the [SDI OUT 14]/[SDI OUT 16] column.f Select the scaling system.