Panasonic AV-HS6000 Operating Manual

Also see for AV-HS6000: Operation guide Firmware upgrade guide

Contents

Panasonic AV-HS6000 Operating Manual Manual pdf 123 page image

– 123 –Chapter 7 CONFIG Menu — Setting the operation modeCHR LIN PinP PinP4CAMERA43CAMERA32CAMERA21CAMERA124ME123BAR22CB221CB120CLIP1V19CLIP1V18STILL2V17STILL1V16CG2V15CG1V14VTR413VTR312VTR211VTR110CAMERA109CAMERA98CAMERA87CAMERA76CAMERA65CAMERA54CAMERA43CAMERA32CAMERA21CAMERA124ME1RECALLCLIP1REGISTERSTOREDELRECALLSHOT MEMORYME1 ME1 ME1XPTME1CB AUXME1STOREDEL23BAR22CB221CB120CLIP1V19CLIP1V18STILL2V17STILL1V16CG2V15CG1V14VTR413VTR312VTR211VTR110CAMERA109CAMERA98CAMERA87CAMERA76CAMERA65CAMERA5MIX0s15fWIPE1s00fWIPE1s00fWIPE1s00fLIN LIN PinP PinPWIPE1s15fWIPE1s15fWIPE2s00fWIPECG5V CG6V CAM1 CAM2CG5V CG6V CAM1 CAM2CG1V CG2V CG3V CG4V2s00fMIX ME22s00fMIX ME12s00fBUSSHFTBUSSHFTME1ME2@@ NOTEt The AUX bus, VMEM bus, DSK bus, DSK operation area, positioner area, and Menu Panel AV-HS60C3 are excluded.1 Select the button → [OPERATE] → [MECHG] tab.2 Select an item in [ME1] and [ME2] in the [MainPanel]/[SubPanel1]/[SubPanel2] column.[ME1] The corresponding ME area is used as ME1.[ME2] The corresponding ME area is used as ME2.f If the item set for [ME1] is switched to [ME2], the item selected for [ME2] is switched to [ME1].f Alternatively, press the button and the button together to switch the ME areas.Setting the key operation modeThe KEY and DSK settings can be preset for each key source of all keyers using the key source preset.f The KEY menus refer to the menu selected from the / button on the top menu → [KEY1] to [KEY4] → [Key Setting]/[Chroma] tab andthe menu selected from the button on the top menu → [DSK1] to [DSK4] → [Setting] tab.@@ NOTEt This function will be available in V2.00.00 or higher.1 Select the button → [OPERATE] → [Key Operate] tab.2 Select an item in [Source Preset] in the [Key Source Preset] column.[Enable]Select this option to adjust the preset for each key source individually.The behavior differs depending on the setting from the button on the top menu → [SOURCE LINK] → [KeyAssign] tab → [Master/Slave].f When [Fill to Source] is selected: The source preset is recalled by the key source linked to the selected key fill.f When [Source to Fill] is selected: The source preset is recalled by the selected key source.[Disable] Select this option to adjust the preset for all common key sources.The source preset is not recalled even when the key source is changed, maintaining the current setting.3 Select an item in [Keyer Link] in the [Key Source Preset] column.f Select the keyer link setting for the source preset.[Enable]For the same key source preset, the keyers are linked to each other. Because the preset setting for the keyers selectingthe same key source shares the identical setting, once an adjustment is done on one keyer, no additional adjustment onother keyers is needed.[Disable] For the same key source preset, each keyer can have different setting.