02/20006-5DocuPrint N2125 GP 1.1General Procedures / InformationInitial IssueGP 1.1 General SpecificationsTable 1 General SpecificationsCategory SpecificationPrinting method Electro-photographic system (roller charging, single com-ponent magnetic toner development)Exposure method Semiconductor Laser Beam ScanningLaser specifications Class 1 Laser ProductClass 3B Laser, rated at 5mW output @ 780nmResolution 600/1200 dots per inch (dpi), switchable at full enginespeed.Fuser method Heat and pressureWarm-up time From a cold start (22°C / 71.6°F ambient temperature) toREADY TO PRINT within 65 seconds.Power supply 100/120VAC (90-140VAC) 50/60Hz (47Hz -63Hz)220/240VAC (198-264VAC) 50/60Hz (47Hz -63Hz)Power consumption 100/120VAC printer: Maximum consumption: 800W Run-ning, 45 W Sleep, Maximum current: 8A (100VAC)/6.66A(120VAC).240VAC printer: Maximum consumption: 800W Running,45W Sleep. Maximum current: 3.33A (240VAC).Note: No electrical current is supplied to the Fuser assem-bly in Sleep Mode.Fuser control temperature 100/120VAC printer: T.B.D°C / °F220/240VAC printer: T.B.D°C / °FSize and weight (not including thePrint Cartridge, System ControllerPWB or any options)Width 422mm X Depth 439mm X Height 413mm (16.5inches x17.25 inches x 16.25 inches)Weight = 26Kg (57lbs)Space requirements Overhead: Minimum T.B.D. mmFront: Minimum 240mm (9.5 inches)Back: Minimum 300mm (11.8 inches)Sides: Minimum T.B.DmmMaximum paper size Legal 14" (8.5"X14" = 355.6mm X 215.9mm)Maximum printable area Edge to edge printing capability. Within the 4mm border (4sides) the printer will print any data 6 point Arial or larger.Maximum paper load 550 sheets of RX 80 A4 paper, or Xerox 20lb Letter sizepaper.Operating environment 5 - 35°C / 41° - 95°F @ 15% to 85% RH (operating)0 - 3100 meter (10171.1 ft.) above sea levelHorizontal bias within 5° of levelStorage environment with apacked Print CartridgeNormal condition:12 months maximum at 0-35°C/32-95°F@ 15-80%RH with no condensation presentSevere condition: 1 month maximum at -20° to 0°C / -4° to32°F or 35° to 40°C / 95 to104°F@ 5-15 or 80-95%RH with no condensation presentStorage environment without apacked Print CartridgeNormal condition: 12 months maximum at -20 to -50°C / -4to -58°F@ 5-85% RH with no condensation presentSevere condition: 48 hours maximum at 50-60°C / 122 -140 °F@ 85-95% RH with no condensation presentAcoustic Noise Standby mode: 35.0dB(A)Sleep mode: Background noise onlyPrinting mode: 49.5dB(A) or 53.0dB(A)Base Engine: Duplex Assembly, Tray 2, Tray 3, EnvelopeFeeder, and OCT.The paper is 20lb Letter SEF, at 600 dpi.Dust generated No more than 0.1mg/m3 of dustPrint Cartridge life (See GP 1.7) *10,000/15,000 prints on A4/Letter paper, with 5% printcoverage(*10,000 or 15,000 prints dependent on Print Cartridgeused)Toner Sensor After Toner Sensor detects a low level of toner in the CRU,the printer makes ten additional prints before generatingan J5 error message.Table 1 General SpecificationsCategory Specification
