02/20006-38 DocuPrint N2025/N2825GP 3.4, GP 3.5Initial IssueGeneral Procedures / InformationSpeed - Ethernet Menu setting to select the speed of the 10/100Base-Tx Ethernet interface.The default setting of “Auto” allows the card to automatically sense the speed of the Ethernetas either 10 or 100 Mbits, automatically sense duplex mode as either half or full. The setting of10/Half or 10/Full forces the card to operate at 10 Mbits in either half or full duplex mode. Thesetting of 100/Half or 100/Full forces the card to operate at 100Mbits in either half or full duplexmode.Speed - Token Ring Menu setting for the default ring speed for the Token Ring interface.Source Routing - Menu setting in the Token Ring menu to select the source routing option.Subnet Mask - Menu setting in the Ethernet or Token Ring menu to manually set the 4 SubnetMask address bytes. This setting is common between the Ethernet and Token Ring menus.This item only appears if "IP Address Res” is set to “Static.”Symbol Set - Menu setting for the default font symbol set used in PCL.System Menu - Menu selection to invoke the "System Menu."Print Menu - Menu selection to invoke the "Print Menu."Test Print - Print a test pattern which can be used by service engineers (and users) to analyzeprint quality. Will cause a printer reset. It will be printed using the PCl number of Print Quantity,default source and default type. All test prints are printed at 600x600 DPI.Token Talk Enable - Token Ring menu setting to enable Token Talk protocol.Token Ring Menu - Menu selection to invoke the Token Ring menu.Tray Menu - Main Menu selection to access tray settings that are common to all system lan-guages (PCL and PostScript).Tray Sequence - Tray Menu setting defining the order in which trays are used when more thanone tray meets the size and type requirements.Tray x Mode - Tray Menu setting to select the paper size installed in this tray is automaticallydetected by the printer, or if the auto detection mechanism is overridden by the values loadedin the Custom Size entry.Tray x Type - Tray Menu setting defining the type of paper installed in each tray. Since theprinter cannot sense the type of paper installed, this parameter must be entered manually foreach tray. There is a separate entry for each tray installed.USB PDL - Menu setting for the default emulation for the USB port.XIE - Menu setting to select the default image (resolution) enhancement mode used in PCLand PostScript.GP 3.5 Non-Menu Control Panel StatesPrinter StatesAfter power is turned on, the printer cycles through Power On Diagnostics, Initialization andWarming Up states before entering the Ready state. The following is the display indication foreach state (Table 1). All states defined in Table 1 are mutually exclusive.Table 1 Power-Up Sequence Display MessagesState Description DisplayP/O Diag. See Ref. 12 See Ref. 12Initializing This state commands the IOT to warm up, starts allsystem tasks, loads NVM parameters into the cur-rent configuration table and starts connectivity proto-cols.Top Line: InitializingBottom Line:Warming-up For the case where the IOT is already warmed up,the display may change from Initializing to Ready,and bypass this display.Top Line: Warming UpBottom Line:Ready In this state, the printer is ready to accept and printdata from any enabled port. It may be overridden byhigher priority messages requiring operator interven-tion such as paper jams or load paper requests. Themessage may be overridden by the PJL "RDYMSG"command.Top Line: ReadyBottom Line:Processing This state is entered when PostScript or PCL is pro-cessing a job. It is overridden by higher priority mes-sages such as paper jams or load paper requests orby the PJL "RDYMSG" command. The Tray No. cur-rently in use is displayed on the bottom line. The Traynumber message is alternated with the "Job Name"on the second line if a name was supplied with thePJL "JOB" command.Top Line: ProcessingBottom Line: name>Waiting This state occurs when either PostScript or PCL iswaiting for input data as defined in the PCL andPostScript Job Flow diagrams. It is overridden byhigher priority messages such as paper jams or loadpaper requests or by the PJL "RDYMSG" command.The Tray number currently in use is displayed on thebottom line. The Tray number message is alternatedwith the "Job Name" on the second line if a namewas supplied with the PJL "JOB" command.Top Line: WaitingBottom Line: name>Bottom Line: Flushing This state occurs in PostScript when flushing a jobdue to a PostScript error or PostScript "Interrupt"command (Control-C). It is not overridden by the PJL"RDYMSG," but is overridden by operator interven-tion conditions, the "Canceling Job" message andmanu selections. The "job name" appears on thesecond line if a name was supplied with the PJL"JOB" command.Top Line: FlushingBottom Line: name>
