02/20006-35DocuPrint N2025/N2825 GP 3.4General Procedures / InformationInitial IssueGP 3.4 Menu Details (Alphabetically)This chapter contains an alphabetic list of all the options found in the menu system. It can beused as a reference in conjunction with the menu maps in chapter 4.Each item is followed by an explanation.AppSocket Bin PS - Ethernet and Token Ring Menu settings to enable/disable the AppSocketbinary mode of PostScript.AppSocket Enable - Menu setting in the Ethernet menu to enable the AppSocket interface.This item is common between the Ethernet and Token Ring MenusAppSocket PDL - Menu setting for the default emulation for the AppSocket interfaceBaud Rate - Serial menu selection to transmission rateBi-Directional - Parallel menu selection to enable/disable the bi-directional modes of the Par-allel portBinary PS - Parallel, Serial and USB Menu settings to enable/disable the binary mode of Post-ScriptCancel Job - Job menu selection to cancel the job currently printing (Postscript or PCL). SeeChapter 6 for a detailed description of this feature.Configure Fuser - Menu selection to allow access to the setting of fuser temperatures associ-ated with each paper type. If this parameter is ON, the list of resident and user defined papertypes (if loaded) is added to the item list for the Tray menu, with a list of values "High," "Normal"and "Low." The default value for Card Stock and Labels is "High." The default value for Trans-parencies is "Low." All other paper types have a default value of "Normal." If "Configure Fuser"is set to "OFF," paper types do not appear in the item list.Config Sheet - Menu selection to print a configuration sheet. Config. sheets will be printedusing the PCL default paper and type. The System Menu setting for number of Print Quantity isignored.Custom Size - Tray Menu setting for the paper size that is to be used for formatting custompaper when a Tray Mode is set to "Custom."Default Gateway - Menu setting in the Ethernet or Token Ring menu to manually set the 4Gateway address bytes. This setting is common between the Ethernet and Token Ring menus.This item only appears if "IP Address Res" is set to "Static."Defaults - System Menu setting for the type of factory defaults to use when a “Factory Default”is performed. The value of this setting is not affected by performing a “Factory Default,” there-fore it does not have a default value apart from the initial value of “Inches” that is used when theprinter is powered up for the first time. It may be manually set to “Millimeters” at the ControlPanel or via a PJL command.Delete All Jobs - Reset Menu selection to delete all Secure and Proof jobs from the disk. Thedisplay indicates "Please Wait" on the bottom line while this action is being processed, andreturns to "ready" when the action is complete. If the disk is locked, the display indicates "DiskLocked" for 10 seconds and then returns to "Ready."Demo Mode - Reset Menu selection to place the printer in the demo mode. Once in this mode,the printer will print demo pages using the eight Control Panel keys to select the type of demopage. Once selected, the printer will enter this state automatically every time the power iscycled. The Demo Mode is entered by power-on while holding down the On-line key and EnterKey, scrolling to the Demo Mode using the Item keys, selecting “Yes” using the Value keys andpushing the Enter button. The Demo mode is exited by power-on while holding down the On-line key and Enter Key. If the Demo mode was enabled when the proceeding power on proce-dure was performed, it is used to exit the Demo mode only, and the Reset menu is not enabled.Demo Page - Print Menu selection to print a demonstration page that shows the printer fea-tures. It will be printed using the PCL default paper size and type at 600 x 600 dpi.Disk Directory - Print Menu setting to request printing the disk directory. Only one copy of thedirectory is printed regardless of the setting of System Menu>Print Quantity.Disk Format - Reset Menu setting to request a complete format of the disk.Disk Unit - Reset Menu setting to request initialization of the disk.Display Faults - Print Menu setting to display the last 50 faults on the Control Panel.DLC/LLC Enable - Menu setting in the Ethernet or Token Ring menu to enable the DLC/LLCprotocol. This item is common between the Ethernet and Token Ring Menus.DLC/LLC Bin PS - Ethernet or Token Ring Menu setting to enable/disable the DLC/DLL binarymode of PostScript.DLC/LLC PDL - Menu setting for the default emulation for the DLC/LLC protocol. This item iscommon between the Ethernet and Token Ring Menus.Draft Mode - System Menu setting to control the reduced toner mode for draft printing.Duplex - Menu setting for Postscript and PCL to set the default duplex mode if installed. LongEdge or Short Edge refers to the printing direction on the back side of the sheet and is also afunction the orientation (landscape or portrait) of the page.Edge to Edge - Menu setting in the System menu to select the printable area in PCL. Settingthis parameters to ON results in all margins of "0" allowing images to be placed at the edge ofthe paper on all sides. The logical page size becomes the physical page size.Ethernet Menu - Menu selection to invoke the Ethernet menu.Ethertalk Enable - Menu setting in the Ethernet menu to enable the Ethertalk protocol.
