Panasonic WJ-HD500B Operating Instructions Manual

Contents

Panasonic WJ-HD500B Operating Instructions Manual Manual pdf 49 page image

49✽✽ indicates the hours for recording time mode:2, 12, 18, 24, 48, 72, 96, 120, 180, 240, 360, 480,720, 960, 1200, 1440, 2160, 2880, 3600, 4320,6480, 8640(parameter A* indicates recording with audio)When the parameter SF/FQ/NQ/EX is selected forrecording time, the recording rate and quality are auto-matically set according to the selected recording time.Note: It may not be possible to set the recording time,depending on the remaining storage capacity of thehard disk.The factory default setting is SF-24H.3. If the parameter SP is selected for recording time, movethe cursor to the REC RATE parameter by pressing theD or C button, then select a recording rate by pressingthe + or - button.1 - 60FPS: Records the selected number of freezeimages every second.0.5FPS: Records a freeze image every 2 seconds.0.4FPS: Records a freeze image every 2.5 seconds.0.3FPS: Records a freeze image every 3.3 seconds.0.2FPS: Records a freeze image every 5 seconds.0.1FPS: Records a freeze image every 10 seconds.Notes:• The maximum recording rate depends on theselected parameters in the COMMON SETUP menuas shown in the table.FIELD/FRAME CAMERA GENLOCK REC RATEFIELD ON 60FPSOFF 30FPSFRAME 3DIM ON 10FPSON OFF 10FPSFRAME 3DIM ON 30FPSOFF OFF 15FPS• “FPS” indicates field per second or frame per sec-ond when the FIELD/FRAME parameter is set toFIELD or FRAME in the menu.Move the cursor to the REC QUALITY parameter bypressing the D or C button, then select a recordingimage quality by pressing the + or - button.SUPER FINE: For enhanced sharpness (CompressionRate 1/6)FINE: For fine image quality (Compression Rate 1/10)NORMAL: For normal image quality (Compression Rate1/16)EXTENDED: For extended time recording quality(Compression Rate 1/25)The factory default setting is SUPER FINE. Event Recording (Manual Recording)These items let you set the recording mode in Time LapseRecording when an alarm is received during manualrecording.1. Move the cursor to the EVENT REC MODE parameterby pressing the D or C button, then select a recordingtime mode by pressing the + or - button.The parameters are the same as MANUAL REC MODE.The factory default setting is SF-24H.2. Move the cursor to the REC RATE(MAX) parameter bypressing the D or C button, then select a recordingrate by pressing the + or - button.For details refer to REC RATE in this menu.3. Move the cursor to the REC QUALITY parameter bypressing the D or C button, then select a recordingimage quality by pressing the + or - button.For details refer to REC QUALITY in this menu.4. Move the cursor to the DURATION parameter by press-ing the D or C button, then select an alarm recordingduration by pressing the + or - button.OFF: Disables alarm recording.2S - 6M: Enables alarm recording for between 2 sec-onds and 6 minutes.MANUAL: Enables alarm recording while the alarm sig-nal is received from the ALARM port.CONTINUE: Enables alarm recording until the RECSTOP is pressed.The factory default setting is 10S.5. Move the cursor to the DYNAMIC REC parameter bypressing the D or C button, then select an alarmrecording pattern by pressing the + or - button.OFF: Records all input images starting from input 1.ALM-PRI: Records the alarmed input images preferen-tially over other video inputs.ALM-ONLY: Records the particular images that haveactivated the alarm.ALM-MULTI: Records multiple alarms adaptively.The factory default setting is OFF.6. If the parameter ALM-MULTI is selected for the alarmrecording pattern, move the cursor to the RECRATE(BASE) parameter by pressing the D or C button,then select a recording rate by pressing the + or -button.The recording rate can be selected as same as RECRATE(MAX) maximally.