E6581595L-11212. Specifications12.1 Models and their standard specifications Standard specificationsItem SpecificationInput voltage class 3-phase 240V classApplicable motor (kW) 0.1 0.2 0.4 0.75 1.5 2.2 3.7Type VFNC3Form 2001P 2004P 2005P 2007P 2015P 2022P 2037PCapacity (kVA) Note 1) 0.3 0.6 1.0 1.6 3.0 4.0 6.5Rated output/current(A) Note 2)0.7(0.7)1.4(1.4)2.4(2.4)4.2(3.6)7.5(7.5)10.0(8.5)16.7(14.0)Output voltage Note 3) 3-phase 200V to 240VRatingOverload current rating 150%-60 seconds, 200%-0.5 secondVoltage-frequency 3-phase 200V to 240V - 50/60HzPowersupplyAllowable fluctuation Voltage 170 to 264V Note 4), frequency ±5%Protective method IP20Cooling method Self-cooling Forced air-cooledColor RAL 3002 / 7016Built-in filter -Item SpecificationInput voltage class 1-phase 120V class 1-phase 240V classApplicable motor (kW) 0.1 0.2 0.4 0.75 0.1 0.2 0.4 0.75 1.5 2.2Type VFNC3SForm 1001P 1002P 1004P 1007P 2001PL 2002PL 2004PL 2007PL 2015PL 2022PLCapacity (kVA) Note 1) 0.3 0.6 1.0 1.6 0.3 0.6 1.0 1.6 3.0 4.0Rated output current(A) Note 2)0.7(0.7)1.4(1.4)2.4(2.4)4.2(4.0)0.7(0.7)1.4(1.4)2.4(2.4)4.2(3.2)7.5(7.5)10.0(9.1)Rated output voltage Note 3) 3-phase 200V to 240V 3-phase 200V to 240VRatingOverload current rating 150%-60 seconds, 200%-0.5 second 150%-60 seconds, 200% -0.5 secondVoltage-frequency 1-phase 100V to 120V – 50/60Hz 1-phase 200V to 240V - 50/60HzPowersupplyAllowable fluctuation Voltage 85 to 132V Note 4), frequency±5% Voltage 170 to 264V Note 4), frequency ±5%Protective method IP20 IP20Cooling method Self-cooling Forced air-cooled Self-cooling Forced air-cooledColor RAL 3002 / 7016 RAL 3002 / 7016Built-in filter - EMI filterNote 1. Capacity is calculated at 220V for output voltage.Note 2. Indicates rated output current setting when the PWM carrier frequency (parameter f300) is 4kHz or less. Between 5kHz and 12 kHz, the rated output current is indicated in the ( ). Above 13 kHz, the output current must be reduced.(See 6.11 in E6581595.)The default setting of the PWM carrier frequency is 12kHz.Note 3. Maximum output voltage is the same as the input voltage.In case of 1-phase 120V class, maximum output voltage is the two times of the input voltage.Note 4. ±10% when the inverter is used continuously (load of 100%).efesotomasyon.com -Toshiba inverter,drive,servo,plc