USO RESTRITO360 Interfacing with External DevicesChapter 19 Switcher Setup5 Select the key you want to be the link destination, thenpress [Key Set].To release a linkUse the same operation as in step 1 to select the linknumber for which you want to release the link setting, thenpress [Clear].Interfacing with ExternalDevicesMaking 9-Pin Port Device InterfaceSettingsThe description in this section takes the Remote S1 port asan example. For the Remote S2 port, carry out the sameprocess as required.1 Open the Engineering Setup >Switcher >DeviceInterface >Remote Assign menu (7337.1).2 Select the device interface you want to set for theRemote S1 port from the group.Editor A: Assigns Editor A to the Remote S1 port.Editor B: Assigns Editor B to the Remote S1 port.AUX: Assigns AUX to the Remote S1 port.The device interfaces which can be selected forRemote S2 are the same as for Remote S1.Making Switcher Processor GPIInput Settings1 Open the Engineering Setup >Switcher >DeviceInterface >GPI Input menu (7337.2).2 Select the setting to apply.3 In the group, select the trigger type.(Rising Edge): Applies the trigger on the risingedge of an input pulse.(Falling Edge): Applies the trigger on thefalling edge of an input pulse.(Any Edge): Applies the trigger on a change inthe polarity of the input signal.(Level): Carries out the specified operationwhen the input is low or high.No Operation: Applies no trigger on an input pulse.4 In the group, select the action block.M/E-1 and P/P: Sets an action for the M/E or PGM/PST bank.Common/Setup: Sets an action for something otherthan the above, or a setup action.5 Select the action.6 Press [Action Set] to confirm the action selection.Selectable actions for various trigger types• When the trigger type is other than “Level”(The x in M/E-x is the M/E bank number, the x in DSKxis the DSK number, and the x in Keyx is the keynumber.)When Target is M/E-x: Cut, Auto Trans, Keyx Cut,Keyx Auto Trans, SS ? Recall, Keyx SS ? Recall,Effect ? Recall, Effect ? Recall & Run, KF Run, KFStop, KF Rewind, KF Rev Run, No ActionWhen Target is P/P: Cut, Auto Trans, DSKx Cut, DSKxAuto Trans, FTB Cut, FTB Auto Trans, SS ? Recall,DSKx SS ? Recall, Effect ? Recall, Effect ? Recall &Run, KF Run, KF Stop, KF Rewind, KF Rev Run,No ActionWhen Target is Common/Setup: FM Src1 Field Freeze,FM Src1 Frame Freeze, FM Src2 Field Freeze, FMSrc2 Frame Freeze, FM Src1 Freeze Off, FM Src2Freeze Off, FM Src1 Clip Record, FM Src1 ClipStop, FM Src2 Clip Record, FM Src2 Clip Stop,FM1 to FM8 Clip Cueup, FM1 to FM8 Clip Play,FM1 to FM8 Clip Stop, User1 to 8 SS ? Recall,User1 to 8 EFF ? Recall, User1 to 8 EFF ? Recall &Run, User1 to 8 KF Run, User1 to 8 KF Stop, User1to 8 KF Rewind, User1 to 8 KF Reverse Run, NoAction• When the trigger type is “Level”(The x in M/E-x is the M/E number.)When Target is M/E-x or P/P: Aspect, Bkgd A SideFlags, Bkgd B Side Flags, No ActionWhen Target is Common/Setup: Format, Aspect, LevelEnable, No ActionFor details about “Level Enable,” see “Notes” in“Making Control Panel GPI Input Settings”(1 p. 337).NotesIf “Format” is selected for “Action” when the formatconverter is used on the switcher, you can set theconversion format of the format converter for “FC Input 1-4,” “FC Input 5-8” and “FC Output 1-2.”Carrying out level settingsTo set the low level and high level, first set the trigger typeto “Level,” then use the following procedure.
