USO RESTRITO32 Names and Functions of Parts of the Control PanelName Description2nd row • Use this to select the cross-point of thebus that is specified with the 1st rowbuttons.a) b)• If the utility/shotbox function is selectedwith the 1st row buttons, use this torecall the register or to execute thefunction.Background ArowUse this to select the signal as thecurrent background video on this M/Ebank or PGM/PST bank.Background BrowUse this to select the signal as thebackground video after the transition onthis M/E bank or PGM/PST bank.Name DescriptionINH SET(inhibit set)Disables button operation.To inhibit operation for a button,press and hold the buttonassigned with [INH SET], andpress the cross-point buttonwhose operation you wish toinhibit.XPT HOLD(cross-point hold)Recalls a keyframe or snapshotwhile maintaining the currentcross-point selection conditions.Available for background A rowand background B row.The following function blocks canbe enabled, depending onsettings in the Setup menu.• Background A and B rows• Key bus• Utility bus• DME external video bus (MVS-6520/6530/3000A only)PRE MCRO(pre-macro)Sets a macro attachment in pre-macro mode.When setting to macro-only mode,this button is used in combinationwith the user preference button onthe menu panel with the “MacroOnly Set” assignment. This modecan also be set by pressing the[PRE MCRO] and [POST MCRO]buttons simultaneously.POST MCRO(post-macro)Sets a macro attachment in post-macro mode.When setting to macro-only mode,this button is used in combinationwith the user preference button onthe menu panel with the “MacroOnly Set” assignment. This modecan also be set by pressing the[PRE MCRO] and [POST MCRO]buttons simultaneously.Chapter 2 Names and Functions of Parts2nd rowBackground A rowBackground B row1) MVS-6520/6530/3000A only2) MKS-6570 only3) MVE-8000A/9000 onlyFor details about assignments, 1 “Assigning a Bus orFunction to 1st Row Buttons” (p. 340).Utility/shotbox functionAssign the function of the [UTIL/SBOX] button, and usefor utility/shotbox operations.When you turn on the button to which [UTIL/SBOX] isassigned, the buttons in the cross-point control block willbe used for utility/shotbox operations.For details, 1 “Executing a Shotbox Function withCross-Point Buttons in the 2nd Row” (p. 280).Assignable buttonsa) You can select the source signal of the key bus by selecting the cross-pointwhile holding down the button to which any of KEY1 to KEY4 or DSK1to DSK4 is assigned in the 1st row.b) You can select the image on the reverse side of the currently viewed DMEimage by selecting the cross-point while holding down the button to whichany of DME1 V/K, DME2 V/K, or DME5 V/K to DME8 V/K is assignedin the 1st row (DME1 V/K and DME2 V/K using MKS-6570 only, andDME5 V/K to DME8 V/K using MVE-8000A/9000 only).Cross-point button numbersCross-point buttons are respectively numbered (1 p. 61).Assigning signals to buttonsYou can assign a signal to each button using the Setupmenu.For details, 1 “Cross-Point Settings” (p. 329).Visual indications on cross-point buttonsFor details, 1 “Colors of lit cross-point buttons” (p. 63).b 1st rowThis selects a key bus, AUX bus, or function.You can assign the following buses, functions, and buttonsin the Setup menu.• KEY1 to KEY4, DSK1 to DSK4, UTIL1, EXT DME1),EDIT PVW, AUX1 to AUX24, FMS1, FMS2,DME1 V/K2), DME2 V/K2), DME5 V/K toDME8 V/K3)• Utility/shotbox function• [INH SET], [XPT HOLD], [PRE MCRO], [POSTMCRO], [MCRO ATTCH ENBL], [KEY], [1ST ROWDSPLY], [2ND ROW DSPLY], [SHIFT] buttons
