Honeywell LYNX Touch Series Installation And Setup Manual

Also see for LYNX Touch Series: User guide Guide Installation and setup guide Programming guide Quick installation guide

Contents

Honeywell LYNX Touch Series Installation And Setup Manual Manual pdf 70 page image

LYNX Touch Installation and Setup Guide- 70 -Regulatory Agency StatementsFederal Communications Commission (FCC) Part 15The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.Unauthorized changes or modifications could void the user's authority to operate the equipment.CLASS B DIGITAL DEVICE STATEMENTNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.FCC IC StatementThis device complies with Part 15 of FCC Rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesiredoperation.Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditionssuivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris lesinterferences causant une reception indésirable.TELEPHONE/MODEM INTERFACEFederal Communications Commission (FCC) Part 68This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number andRinger Equivalence Number (REN). You must provide this information to the telephone company when requested.This equipment uses the following USOC jack: RJ31XThis equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This equipment ishearing-aid compatible.Industry CanadaNOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications networkprotective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). TheDepartment does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the aboveconditions may not prevent degradation of service in some situations.Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to thisequipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment.Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipesystem, if present, are connected together, This precaution may be particularly important in rural areas.Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, asappropriate.AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection,d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relativesau matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Lematériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que laconformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunicationspeut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvaisfonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques et descanalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des installationsélectriques, ou à un électricien, selon le cas.Ringer Equivalence Number Notice:The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to beconnected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that thesum of the Ringer Equivalence Numbers of all the devices does not exceed 5.AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent êtreraccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule conditionque la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.!RF ExposureWARNING: The LYNX Touch must be installed to provide a separation distance of at least 7.8 in (20 cm) from allpersons and not co-located or operated in conjunction with any other transmitter except in accordance with FCCmulti-transmitter product procedures.