Honeywell Vigilon 4 loop manuals

Vigilon 4 loop

Brand: Honeywell | Category: Control Panel

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Preliminary information
5. Points to remember
6. A typical commissioning process
7. Product Approval and Standards
8. S-Cubed Mark 3
9. S-Quad Sensors (Legacy product range)
10. S-Cubed Mark 2 (Legacy product range)
11. Fire Panels
12. Controls and indications
13. Vigilon 4/6 loop Panels
14. Fitting the inner door
15. Printer paper roll
16. Setting the DKC card
17. Card installation
18. Terminals on Terminal Card
19. Pre power-up checks
20. Battery installation
21. PSU LED indications
22. Fire Routing LEDs (Post Mid 2015)
23. How to configure the 'U' buttons
24. Vigilon Compact Panel
25. Cards and internal cables of the panel
26. Installing a replacement MCB in an older Vigilon Compact panel
27. Terminals on the Master Control Board (MCB)
28. Settings on the DKC
29. Pre Power up checks
30. Mains supply
31. How to configure the monitored input
33. How to configure the U1 and U2 buttons
34. Factory settings
35. Vigilon Compact Voice Alarm Panel - (legacy product)
37. Terminals on the Audio Control Card
38. Terminals on the Master Control Board
41. How to check and set the audio signal
42. Indications on power up
43. Useful menu options
44. How to create an Engineer PIN
45. Address allocation
46. Allocation faults
47. SAFE Addressing
48. Checking a loop map
49. Non Volatile Memory (NVM)
50. NVM Software - 'write protect' and 'unprotect
51. To recover loop data from NVM
52. km Loop circuit - tests using LDT
53. Loop circuit tests
54. Positive line break test
55. Checking device STATUS
56. Plexus Device Status
57. Device checks
58. Checking the Exception/Subfault codes
59. Condition Codes for S-Quads (Exception / Sub Fault codes)
60. Pre Fire, Fire and Super fire
61. S-Quad Sensor with VAD - STATES VAD (current range of devices)
62. S-Quad Sensor with Strobe - STATES (legacy devices)
63. S-Quad Heat sensor STATES
64. S-Quad Dual Optical, Heat & CO sensor STATES
65. Beam sensor STATES
66. Interface Unit STATES
67. range of sensors STATES (legacy devices)
68. Heat sensor STATES (34000 range)
69. Installed equipment tests
70. Fire Sensors
71. Cubed
72. Vigilon Compact Network
73. Wiring the single network
74. Network Card for VIGILON Compact - baud and node address switch settings
75. Powering-up the Network
76. How to check Network Card status
77. Single Vigilon Network
78. Wiring a Copper network
79. Single network without domain bridge
81. Multiple Vigilon Networks
82. IO domain bridge network switch settings
83. Message routing
84. Domain bridge message passing tests
85. FO Domain Network switch settings
86. Appendix A-1 - Menu maps for EN54 (V4) Vigilon panel
87. Appendix A-2 - Menu maps for BS (V3+) Vigilon panel
88. Appendix B - Message Action List
89. Message Action list
90. Appendix C - Guidelines for standalone system commands
91. Long labels
92. Sectors
93. Integral sounder operation
94. Default fire plan
95. Delay Blocks
96. Sound and Resound alarms options
97. Time slots and Time blocks
98. Zones
99. Zone Tasks
100. Command Builds
101. Sounders Configuration
102. Auxiliary Relays
103. Fire Alarm Routing Equipment (FARE)
104. Fire Protection Equipment (FPE)
105. S-Cubed Mark III or II and S-Quad
106. Voice and Sounder mode pluse VAD/Strobe action
107. Appendix D - Guidelines for Networked system commands
108. Master Groups
109. Appendix E - Cards