Panasonic WV-NP472 Operating Instructions Manual

Also see for WVNP472 - COLOR CCTV CAMERA: Brochure Reference Reference Specifications

Panasonic WV-NP472 Operating Instructions Manual Manual pdf 21 page image

-21-10. Special MenuThis menu lets you adjust and set up the video signal ofthe camera to meet your requirements.Move the cursor to RET in the bottom line of the CAMSET UP menu and press L and M simultaneously(holding down L and press M) for 2 seconds ormore. The SPECIAL menu appears on the monitorscreen.10-1. Camera Picture Upside Down Positioning(UP SIDE DOWN)1. Move the cursor to UP SIDE DOWN.2. Select ON when you want to turn the picture upsidedown.Note: The right and left of the picture are notreversed.10-2. Chroma Gain Setting (CHROMA GAIN)1. Move the cursor to CHROMA GAIN.2. While observing the vectorscope or color videomonitor, move the “I” cursor to adjust the chromalevel.10-3. Aperture Gain Setting (AP GAIN)1. Move the cursor to AP GAIN.2. While observing the waveform monitor or colorvideo monitor, move the “I” cursor to adjust theaperture gain.10-4. Pedestal Level Setting (PEDESTAL)1. Move the cursor to PEDESTAL.2. While observing the waveform monitor or colorvideo monitor, move the “I” cursor to adjust thepedestal level (black level).10-5. Chroma Phase (Hue) Setting (HUE)1. Move the cursor to HUE.2. While observing the vectorscope or color videomonitor, move the “I” cursor to adjust the hue(chroma phase) level.10-6. BWThis function lets you select the color or black-and-white mode.1. Move the cursor to BW.2. Select AUTO1, AUTO2, EXT, ON or OFF using Lor M.AUTO1: The camera selects the black and whitemode if the picture is dark, or the color mode ifthe picture is bright enough.AUTO2: Applying AUTO1 may cause malfunctionwhen using a source of near-infrared light at** CAM SET UP **CAMERA ID OFFALC/ELC ALCSHUTTER ---AGC ON(DNR-H)SENS UP OFFSYNC INTWHITE BAL ATW1MOTION DET OFFLENS DRIVE DCCLOCK OFFRET↵↵↵** SPECIAL **UP SIDE DOWN OFFCHROMA GAIN ....I....AP GAIN ....I....PEDESTAL .I.......HUE .I.......- +BW OFFBURST(BW) ONCAMERA RESET /PUSH SWRET ENDnight because the illuminance changes signifi-cantly when switching between a color pictureand a black-and-white picture. This can beprevented by using the AUTO2 setting todetect the type of light source.Note: Because the type of light source isdetected based on information receivedfrom the CCD image pickup element, anobject that is constantly moving or has thesame color as its background may notalways be properly recognized. Whenchoosing the AUTO2 mode, make sure touse a light source having a wavelength of800 nm or more.EXT: Color picture reverts to black-and-white pic-ture when an external day/night switching sig-nal is received (refer to alarm connections).ON: Black-and-white mode enabled.OFF: Color mode enabled.The factory default setting is OFF.3. The AUTO1 or AUTO2 menu appears on the moni-tor screen when selected.4. Move the cursor to LEVEL and select the illumi-nance level using L or M.** BW AUTO1 **LEVEL HIGHDURATION TIME .I..S LRET ENDLOW: Color picture switches to black-and-whitepicture at approx.1 lx with F1.4 lens.HIGH: Color picture switches to black-and-whitepicture at approx.5 lx with F1.4 lens.The factory default setting is HIGH.5. Move the cursor for DURATION TIME to set theswitching time using L or M.The following switching times are available:10s--30s--60s--300s(S) (L)10-7. BURST (BW)1. Move the cursor to BURST (BW).2. Select ON or OFF using L or M.ON: The burst signal is supplied along with theblack-and-white composite video signal.OFF: The burst signal is not output.The factory default setting is ON.Notes:• We recommend that you usually select ON.• When the camera is used to synchronize thesystem for external sync, select ON to preventa malfunction.