Panasonic WV-NP472 Operating Instructions Manual

Also see for WVNP472 - COLOR CCTV CAMERA: Brochure Reference Reference Specifications

Panasonic WV-NP472 Operating Instructions Manual Manual pdf 20 page image

-20-Manual Fine Adjustment for AWC (ATW)You can set the white balance items manually.1. To set MASK SET, proceed as described in steps 2to 4 of “ALC mode with SUPER-D2 OFF and ELCmode”.2. Move the cursor to R.3. Press L or M to obtain the optimum amount ofred gain.4. Move the cursor to B.5. Press L or M to obtain the optimum amount ofblue gain.Note: When you need to set MASK SET, re-adjust toobtain the optimum amount of red and blue gain.7. Motion Detector Setting (MOTION DET)The camera detects moving objects in the scene bymonitoring changes in brightness level. You can selectthe level of sensitivity for motion detection.When this camera is connected to a compatible intelli-gent CCTV system, the camera transmits an alarm sig-nal by multiplexing it with the video signal.1. Move the cursor to MOTION DET and select ON.The factory default setting is OFF.2. Press I. The MOTION DETECT menu appearson the monitor screen.** MOTION DETECT **LEVEL ....I....- +DISPLAY MODEALARM OFFMASK SETRET END↵↵3. Move the cursor to MASK SET and press I.MASK SET lets you set 48 mask areas. To setMASK SET, proceed as described in steps 2 to 4 of“ALC mode with SUPER-D2 OFF and ELC mode”.4. Move the cursor to ALARM and select ON or OFFto set the alarm for DISPLAY MODE.Note: When using the WV-RM70, WV-CU550series, WV-CU161 or WV-CU360 controllerwith this model, select OFF for ALARM.5. Move the cursor to DISPLAY MODE and press Ito see the current setting. The masks that detectthe brightness changes start blinking.6. To raise detection sensitivity, press I to return tothe MOTION DETECT menu.7. To obtain the optimum detection level, move the “I”cursor to adjust the level.8. Repeat the procedure above to obtain a satisfacto-ry setting.Notes:• When the camera is not used in a PanasonicIntelligent CCTV System, select OFF.Otherwise, video equipment may malfunctionbecause of the alarm signal misinterpretation for atime code signal.• The motion detector may malfunction when thelightening equipment continuously turns on and off,or when ELC mode is selected for ALC/ELC.• Set MASK SET over the areas where swayingleaves, curtains, or other objects are detected.• Adjust the detection level on the menu to preventmisinterpretation under low light conditions withnoise.• It takes about 0.2 seconds for the alarm signal toreach the VCR’s alarm terminal after the cameradetects a moving object.• The motion detector is not specifically intended toprevent theft or fire.8. Lens Drive Signal Selection (LENS DRIVE)Select a signal form matching to the lens installed. Thefactory setting is DC.DC: Is applied to a DC driven type lens.VIDEO: Is applied to a video signal type lens.** CLOCK **CLOCK TYPE MM/DD/YYYYRET END9. Date Display (Clock) SettingYou can select a display position and a style of the datedisplay. The camera ID will be displayed under theposition designated here.1. In the camera setup menu, move the cursor toCLOCK, and press M or L to select a displayposition.OFF: Does not display the date.ON (L-UP): Displays at the left-upper corner.ON (L-LOW): Displays at the left-lower corner.ON (R-UP): Displays at the right-upper corner.ON (R-LOW): Displays at the right-lower corner.2. Move the cursor to CLOCK, and press I.The CLOCK menu opens.3. Select a style with L and M.YYYY/MM/DD: Year/Month/DayMM/DD/YYYY: Month/Day/YearDD/MM/YYYY: Day/ Month/Year