Panasonic WV-NP472 Operating Instructions Manual

Also see for WVNP472 - COLOR CCTV CAMERA: Brochure Reference Reference Specifications

Panasonic WV-NP472 Operating Instructions Manual Manual pdf 19 page image

-19-5. Electronic Sensitivity Enhancement(SENS UP)There are two modes for SENS UP.AUTO: If you select X10 AUTO, for example, thesensitivity is automatically raised to X10 max.When AUTO is selected, AGC is automaticallyset to ON.FIX: If you select X32 FIX, for example, the sensitiv-ity is raised to just X32.The factory default setting is OFF.Move the cursor to SENS UP and select the parameterfor electronic sensitivity enhancement.The preset values for SENS UP (electronic sensitivityenhancement) change by pressing L or M asshown below:Notes:• When ON is selected for SUPER-D2 in the ALCCONT menu, FIX is not available for this item.• When you select AUTO for SENS UP and ON forSUPER-D2, the SENS UP function has priority sothat the SUPER-D2 function is not activated auto-matically.• While the SENS UP function is selected, noise,spots or a whitening phenomenon may appear inthe picture when the sensitivity of the camera isincreased. This is a normal phenomenon.6. White Balance Setting (WHITE BAL)6-1. Auto-Tracing White Balance Mode (ATW)You can select one of three modes for white balanceadjustment as follows:The factory default setting is ATW1.• ATW1 (Auto-Tracing White Balance 1)Move the cursor to WHITE BAL and select ATW1.In this mode, the color temperature is monitoredcontinuously and thereby white balance is automat-ically set. The color temperature range for theproper white balance is approximately 2 600 - 6000 K. Proper white balance may not be obtainedunder the following conditions:1. The color temperature is out of the 2 600 - 6 000 Krange.2. When the scene contains mostly high color temper-ature objects, such as a blue sky or sunset.3. When the scene is dim.In these cases, select the AWC mode.• ATW2 (Auto-Tracing White Balance 2)Auto-tracing white balance in the sodium lampmode (ATW2)When you select ATW2 for sodium lamp, white bal-ance is automatically set (no operation needed).Note: ATW1 and ATW2 do not appear for WHITEBAL on the system controller setup menu.• Automatic White Balance Control Mode (AWC)In this mode, accurate white balance is obtainedwithin a color temperature range of approximately2 300-10 000 K.X2 AUTOOFF X4 AUTO X6 AUTO X10 AUTOX32 FIX X10 FIX X6 FIX X4 FIX X2 FIXOFFX16 FIX** CAM SET UP **CAMERA ID OFFALC/ELC ALCSHUTTER ---AGC ON(DNR-H)SENS UP OFFSYNC INTWHITE BAL ATW1MOTION DET OFFLENS DRIVE DCCLOCK OFFRET↵↵ ↵** CAM SET UP **CAMERA ID OFFALC/ELC ALCSHUTTER ---AGC ON(DNR-H)SENS UP OFFSYNC INTWHITE BAL AWC→PUSH SWMOTION DET OFFLENS DRIVE DCCLOCK OFFRET↵↵Highlighted1. Move the cursor to WHITE BAL and select AWC →PUSH SW.2. Press I to start white balance setup. PUSH SWis highlighted to indicate that white balance isbeing set.3. When the white balance setting is completed,PUSH SW returns to normal display.Note: If white balance is not set, PUSH SW is beinghighlighted.4. When you want to adjust white balance manually,press M to select AWC and press I. The AWCmenu appears on the monitor screen. (When ATWis selected, pressing I displays the ATW menu.)** AWC **R ....I....- +B ....I....- +MASK SETRET END↵