YASKAWA P1000 Quick Start Manual

Also see for P1000: Technical manual Quick start guide Safety precautions Technical manual Installation manual

Contents

YASKAWA P1000 Quick Start Manual Manual pdf 205 page image

u H2: Multi-Function Digital OutputsNo.(Addr.Hex) Name Description Values PageH2-01(40B) Terminal M1-M2 functionselection (relay) Refer to H2 Multi-Function Digital Output Settings on pages 205 to 206 fordescriptions of setting values. Default: 0Range: 0 to 192 108H2-02(40C) Terminal M3-M4 functionselection (relay) Default: 1Range: 0 to 192 108H2-03(40D) Terminal MD-ME-MFFunction Selection Default: 2Range: 0 to 192 108H2-06(437) Watt Hour Output UnitSelectionOutputs a 200 ms pulse signal when the watt-hour counter increases by theunits selected.0: 0.1 kWh units1: 1 kWh units2: 10 kWh units3: 100 kWh units4: 1000 kWh unitsDefault: 0Range: 0 to 4 –H2 Multi-Function Digital Output SettingsH2-ooSetting Function Description Page0 During run Closed: A Run command is active or voltage is output. –1 Zero speed Open: Output frequency is above the minimum output frequency set in E1-09.Closed: Output frequency is below the minimum output frequency set in E1-09. –2 Speed agree 1 Closed: Output frequency equals the speed reference (plus or minus the hysteresis set to L4-02). 1093 User-set speed agree 1 Closed: Output frequency and speed reference equal L4-01 (plus or minus the hysteresis set toL4-02). 1104 Frequency detection 1 Closed: Output frequency is less than or equal to the value in L4-01 with hysteresis determinedby L4-02. –5 Frequency detection 2 Closed: Output frequency is greater than or equal to the value in L4-01 with hysteresis determinedby L4-02. –6 Drive ready Closed: Power up is complete and the drive is ready to accept a Run command. –7 DC bus undervoltage Closed: DC bus voltage is below the Uv trip level set in L2-05. –8 During baseblock (N.O.) Closed: Drive has entered the baseblock state (no output voltage). –9 Frequency reference source Open: External Reference 1 or 2 supplies the frequency reference (set in b1-01 or b1-15).Closed: Digital operator supplies the frequency reference. –A Run command source Open: External Reference 1 or 2 supplies the Run command (set in b1-02 or b1-16).Closed: Digital operator supplies the Run command. –B Torque detection 1 (N.O.) Closed: An overtorque or undertorque situation has been detected. –C Frequency reference loss Closed: Analog frequency reference has been lost.Frequency reference loss is detected when the frequency reference drops below 10% of thereference within 400 ms. –D Braking resistor fault Closed: Braking resistor or transistor is overheated or faulted out. –E Fault Closed: Fault occurred. –F Through mode Set this value when using the terminal in the pass-through mode. –10 Minor fault Closed: An alarm has been triggered, or the IGBTs have reached 90% of their expected life span. –11 Fault reset command active Closed: A command has been entered to clear a fault via the input terminals or from the serialnetwork. –12 Timer output Closed: Timer output. –13 Speed agree 2 Closed: When drive output frequency equals the frequency reference ±L4-04. –14 User-set speed agree 2 Closed: When the drive output frequency is equal to the value in L4-03 ±L4-04. –15 Frequency detection 3 Closed: When the drive output frequency is less than or equal to the value in L4-03 ±L4-04. –16 Frequency detection 4 Closed: When the output frequency is greater than or equal to the value in L4-03 ±L4-04. –17 Torque detection 1 (N.C.) Open: Overtorque or undertorque has been detected. –18 Torque detection 2 (N.O.) Closed: Overtorque or undertorque has been detected.19 Torque detection 2 (N.C.) Open: Overtorque or undertorque has been detected. –1A During reverse Closed: Drive is running in the reverse direction. –1B During baseblock (N.C.) Open: Drive has entered the baseblock state (no output voltage). –B.6 H Parameters: Multi-Function TerminalsYASKAWA ELECTRIC TOEP YAIP1U 01B YASKAWA AC Drive - P1000 Quick Start Guide 205B Parameter List