KEPCO BOP-MG Operator's Manual

Contents

KEPCO BOP-MG Operator's Manual Manual pdf 19 page image

BOP-1K 031912 ixLIST OF TABLESTABLE TITLE PAGE1-1 BOP 1000 Watt Model Parameters .............................................................................................................1-11-2 BOP General Specifications .......................................................................................................................1-21-3 Equipment Supplied ....................................................................................................................................1-161-4 Safety Symbols ...........................................................................................................................................1-161-5 Accessories .................................................................................................................................................1-182-1 Rear Panel Connector Functions ................................................................................................................2-22-2 IEEE 1118 Connector Input/Output Pin Assignments .................................................................................2-22-3 Trigger Port Pin Assignments .....................................................................................................................2-32-4 External Protection Connector Input/Output Pin Assignments ....................................................................2-32-5 RS232C PORT Input/Output Pin Assignments ...........................................................................................2-42-6 Parallel/Serial Control Out Port Pin Assignments .......................................................................................2-42-7 Parallel/Serial Control In Port Pin Assignments ..........................................................................................2-42-8 Parallel/Serial Protect In Port Pin Assignments ..........................................................................................2-52-9 Parallel/Serial Protect Out Port Pin Assignments .......................................................................................2-52-10 Analog I/O Port Input/Output Pin Assignments ...........................................................................................2-62-11 IEEE 488 Port Input/Output Pin Assignments .............................................................................................2-72-12 Multiple Units Menu Functions ....................................................................................................................2-202-13 Slave Status Message Definitions ..............................................................................................................2-223-1 Front Panel Controls and Indicators ...........................................................................................................3-23-2 Special Key Functions ................................................................................................................................3-33-3 Display (Operator Convenience) Menu Functions ......................................................................................3-103-4 Voltage and Current Parameter Definitions ................................................................................................3-133-5 Max/Min Settings Menu ..............................................................................................................................3-173-6 Power Supply Behavior when Output is set to OFF ....................................................................................3-203-7 Examples Showing How Power-up Settings Function ................................................................................3-223-8 Save/recall menu ........................................................................................................................................3-233-9 Sine, Triangle and Ramp Waveform Frequency vs. Points ........................................................................3-283-10 Square Waveform Frequency vs. Points ....................................................................................................3-283-11 Waveform Segment Details Menu ..............................................................................................................3-313-12 New Waveform Settings Menu ...................................................................................................................3-323-13 Revisions/test Menu ....................................................................................................................................3-353-14 Error Message Explanations .......................................................................................................................3-363-15 Analog Remote Setup Menu .......................................................................................................................3-403-16 Interface Settings Menu ..............................................................................................................................3-463-17 Operation of #RST Command ....................................................................................................................3-473-18 IEEE 488 (GPIB) Bus Interface Functions ..................................................................................................3-493-19 IEEE 488 (GPIB) Bus Command Mode Messages .....................................................................................3-503-20 IEEE 488 (GPIB) Bus Data Mode Messages ..............................................................................................3-503-21 Rules Governing Shortform Keywords ........................................................................................................3-614-1 Calibration Summary ..................................................................................................................................4-14-2 Suggested Sense Resistors ........................................................................................................................4-34-3 Voltage Calibration Measurements and Tolerances ...................................................................................4-34-4 Current Calibration Measurements and Tolerances ...................................................................................4-44-5 Calibration Storage .....................................................................................................................................4-16A-1 IEEE 488.2 Command/query Index ........................................................................................................... A-1A-2 Standard Event Status Enable Register and Standard Event Status Register Bits ................................... A-1A-3 Service Request Enable and Status Byte Register Bits ............................................................................. A-5A-4 Built-in test Error Codes ............................................................................................................................. A-6B-1 SCPI Subsystem Command/query Index .................................................................................................. B-1B-2 List Data Table ........................................................................................................................................... B-15B-3 Operation Condition Register, Operation Enable Register,and Operation Event Register Bits .......................................................................................................... B-29B-4 Questionable Event Register, Questionable Condition Registerand Questionable Condition Enable Register Bits .................................................................................. B-30B-5 Error Messages .......................................................................................................................................... B-36