Contents - power supply
- declaration of conformity
- safety instructions
- safety messages
- warnings and cautions
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Scope of Manual
- input characteristics
- miscellaneous features
- physical characteristics
- W BOP Power Supply, Outline Drawing
- rear view
- Local Control
- Saving and Recalling Settings
- Energy Recuperation
- BOP Output Characteristics
- Accessories
- Unpacking and Inspection
- Rear Panel Connector Functions
- Trigger Port Pin Assignments
- RS232C PORT Input/Output Pin Assignments
- Parallel/Serial Protect In Port Pin Assignments
- preliminary operational check
- IEEE 488 Port Input/Output Pin Assignments
- Installation
- Grounding Network Configuration
- Load Connection - General
- Load Connection Using Local Sensing
- Load Connections, Local Sensing
- Setup for Remote Operation via GPIB
- Multiple Unit Source Power
- Parallel Configuration, Local Sensing, Typical
- Parallel Configuration, Remote Sensing, Typical
- Series Configuration, Local Sensing, Typical
- Series Configuration, Remote Sensing, Typical
- Configuring Parallel, Series, 2 X 2 or 3 X 2 combinations
- Multiple Units Menu Functions
- Master Power Up Screen
- Power On Default Screen for Master Unit
- Operating Instructions for Multiple Unit Combinations
- Restoring a Unit to Standalone Operation
- x 2 (3 Series X 2 Parallel) Configuration, Local Sensing, Typical
- General
- Front Panel Keypad
- LCD and Power-up Screen Description
- Power-up Screen Showing Graphic Meters
- Turning the Power Supply On
- How to Access the menus
- How to Modify a Parameter
- How to Access a Password Protected Menu
- Operator Convenience Functions (Display Menu)
- Displaying Programmed Settings in RemoTe Mode
- Enabling/Disabling Audible Beeps
- Local Password Protection at Power-up
- Voltage and Current Parameter Definitions
- Selecting Bipolar/Independent Protection Limits
- General Setup Menu
- Understanding Voltage and Current Protect Limits
- Changing Maximum Accepted Voltage or Current (Main Channel Software Limits)
- Changing Maximum/Minimum Protection Software-controlled Limits
- External Limits
- Determining How the Unit responds when Output is OFF (Load Type)
- Changing the Default Power up Settings
- Examples Showing How Power-up Settings Function
- Storing/Recalling Power Supply Output Settings
- Viewing Saved Settings
- Copying Previously Saved settings to a New Location
- Applying Saved settings to the Output (Recall)
- Understanding How Waveforms Are Generated
- Waveform Specifications
- Viewing Stored Waveforms
- Modifying Previously Stored Waveforms
- Waveform Segment Details Menu
- Using Segments to Build a Waveform
- Sample Waveform
- Copying a Waveform
- Reset
- Error Message Explanations
- Analog Remote Mode Programming
- Remote Standby
- Voltage/Current Mode Control
- Analog Remote Setup Menu
- Variable Gain Using External Reference Level
- External Protection Limits
- Monitoring Output Current Using an analog signal
- Making Sure the Previous Command is Complete
- Remote Mode Setup
- GPIB Port Setup
- Determining Whether *RST Command sets the Output Off or On
- Configure Prompt Mode
- Status Reporting Differences in BIT 4886
- BOP VISA Instrument driver
- RS232-C Operation
- RS 232 Implementation
- XON XOFF Method
- Isolating RS 232 Communication Problems
- Common Commands/Queries
- system subsystem
- MEASure Subsystem
- TRIGger subsystem
- Program Message Structure
- Keyword Separator
- Message Unit Separator
- Program Message Syntax Summary
- Status Reporting Structure
- Typical Example Of BOP Power Supply Program Using SCPI Commands
- Operational Status Register
- QUEStionable Status Register
- Test Equipment Requirements
- Suggested Sense Resistors
- Calibration using Remote SCPI commands via GPIB or RS 232 Interface
- Calibration Procedure using SCPI Commands
- Calibration Setup for Current Mode
- Calibration Using Front Panel Keypad in Local Mode
- Main Calibration Screen
- Calibration Procedure using Local Mode
- Calibration Storage
- A.2 *CLS — Clear Status Command
- A.4 *ESE? — Standard Event Status Enable Query
- A.8 *OPC? — Operation Complete Query
- A.9 *OPT? — Options Query
- A.13 *SRE — Service Request Enable Command
- A.17 *TST? — Self Test Query
- B.1 Introduction
- B.2 Numerical Values
- B.5 INIT iate [:IMM ediate ] Command
- B.6 INIT iate :CONT inuous Command
- B.12 MEM ory :UPD ate Command
- ut [:STAT e ] Command
- ut :CONT rol Command
- el ]:LIM it [:BOTH] Command
- el ]:LIM it :NEG Command
- ce :]CURR ent :MODe? Query
- el ]:PROT ect :NeG ative ? Query
- ce :]FUNC tion :MODE? Query
- B-5 Using LIST Commands and Queries
- t Command
- B-2 List Data Table
- APPL y :SWE ep Command
- Command
- VOLT age Command
- BOP-1K
- B-6 Using List:WAIT Commands to Control Generation of a Waveform Measured by Multiple External Devices using a Single External Pulse
- age :APPL y Command
- B.84 [SOUR ce :]LIST:WAIT:LEDGe Command
- LEV el ]:LIM it [:BOTH]? Query
- LEV el ]:LIM it :pos itive ? Query
- B-9 Using PROT:LIM:POS and PROT:LIM:POS Commands to Set Asymmetrical Limits
- LEV el ]:PROT ect :POS itive Command
- Query
- B-4 Questionable Event Register, Questionable Condition Register and Questionable Condition Enable Register Bits
- B-10 Using Status Commands and Queries
- B.128 SYSTem:COMMunication:SERial:PACE Command
- B.130 SYSTem:COMMunication:SERial:PROMpt CommanD
- STAT e ? Query
- B-12 Using System Commands and Queries
- B-5 Error Messages
|
BOP-1K 031912 vTABLE OF CONTENTSSECTION PAGEB.13 OUTPut [:STATe ] Command................................................................................................................... B-6B.14 OUTPut [:STATe ] Query ......................................................................................................................... B-7B.15 OUTPut :CONTrol Command ................................................................................................................. B-7B.16 OUTPut :CONT? Query .......................................................................................................................... B-7B.17 OUTPut :MODE Command..................................................................................................................... B-7B.18 OUTPut :MODE? Query.......................................................................................................................... B-7B.19 [SOURce :]CURRent[:LEVel][:IMMediate ][:AMPlitude ] Command ...................................................... B-7B.20 [SOURce :]CURRent[:LEVel][:IMMediate ][:AMPlitude ] Query ............................................................. B-7B.21 [SOURce :]CURRent[:LEVel]:LIMit[:BOTH] Command.......................................................................... B-8B.22 [SOURce :]CURRent[:LEVel]:LIMit[:BOTH]? Query .............................................................................. B-8B.23 [SOURce :]CURRent[:LEVel]:LIMit:NEG Command.............................................................................. B-9B.24 [SOURce :]CURRent[:LEVel]:LIMit:NEG? Query................................................................................... B-9B.25 [SOURce :]CURRent[:LEVel]:LIMit:POS Command .............................................................................. B-9B.26 [SOURce :]CURRent[:LEVel]:LIMit:POS? Query................................................................................... B-9B.27 [SOURce :]CURRent:MODE Command................................................................................................. B-9B.28 [SOURce :]CURRent:MODe? Query...................................................................................................... B-10B.29 [SOURce :]CURRent[:LEVel]:PROTect[:BOTH] Command................................................................... B-10B.30 [SOURce :]CURRent[:LEVel]:PROTect[:BOTH] Query.......................................................................... B-10B.31 [SOURce :]CURRent[:LEVel]:PROTect:MODE Command .................................................................... B-10B.32 [SOURce :]CURRent[:LEVel]:PROTect:MODE? Query......................................................................... B-10B.33 [SOURce :]CURRent[:LEVel]:PROTect:NeG ative Command ............................................................... B-10B.34 [SOURce :]CURRent[:LEVel]:PROTect:NeG ative ? Query.................................................................... B-11B.35 [SOURce :]CURRent[:LEVel]:PROTect:POSitive Command ................................................................ B-11B.36 [SOURce :]CURRent[:LEVel]:PROTect:POSitive? Query..................................................................... B-11B.37 [SOURce :]CURRent[:LEVel]:PROTect:LIMit[:BOTH] Command.......................................................... B-11B.38 [SOURce :]CURRent[:LEVel]:PROTect:LIMit[:BOTH]? Query............................................................... B-11B.39 [SOURce :]CURRent[:LEVel]:PROTect:LIMit:NeG ative Command ...................................................... B-11B.40 [SOURce :]CURRent[:LEVel]:PROTect:LIMit:NeG ative? Query........................................................... B-11B.41 [SOURce :]CURRent[:LEVel]:PROTect:LIMit:POSitive Command ....................................................... B-12B.42 [SOURce :]CURRent[:LEVel]:PROTect:LIMit:POSitive ? Query............................................................ B-12B.43 [SOURce :]CURRent[:LEVel]:TRIGgered[:AMPlitude] Command ....................................................... B-12B.44 [SOURce :]CURRent[:LEVel]:TRIGgered[:AMPlitude]? Query ............................................................ B-12B.45 [SOURce :]FUNCtion :MODE Command ................................................................................................ B-12B.46 [SOURce :]FUNCtion :MODE? Query..................................................................................................... B-12B.47 [SOURce :]FUNCtion :MODE:TRIGger Command................................................................................. B-12B.48 [SOURce :]FUNCtion :MODE:TRIGger ? Query ..................................................................................... B-13B.49 [SOURce :]LIST:CLEar Command ......................................................................................................... B-13B.50 [SOURce :]LIST:COUNt Command........................................................................................................ B-14B.51 [SOURce :]LIST:COUNt? Query............................................................................................................. B-14B.52 [SOURce :]LIST:COUNt:SKIP Command............................................................................................... B-15B.53 [SOURce :]LIST:COUNt:SKIP? Query.................................................................................................... B-15B.54 [SOURce :]LIST:CURRent Command.................................................................................................... B-15B.55 [SOURce :]LIST:CURRent? Query......................................................................................................... B-15B.56 [SOURce :]LIST:CURR:APPLy Command ............................................................................................. B-16B.57 [SOURce :]LIST:CURRent:APPLy:SWEep Command .......................................................................... B-16B.58 [SOURce :]LIST:CURRent:APPLy:SWEep? Query............................................................................... B-16B.59 [SOURce :]LIST:CURRent:POINts? Query............................................................................................ B-16B.60 [SOURce :]LIST:DWELl Command ........................................................................................................ B-16B.61 [SOURce :]LIST:DWELl ? Query ............................................................................................................. B-17B.62 [SOURce :]LIST:DWELl :POINts? Query ................................................................................................ B-17B.63 [SOURce :]LIST:QUERy Command ....................................................................................................... B-17B.64 [SOURce :]LIST:QUERy? Query ............................................................................................................ B-17B.65 [SOURce :]LIST:REPeat Command....................................................................................................... B-17B.66 [SOURce :]LIST:RESolution ? Query ..................................................................................................... B-17B.67 [SOURce :]LIST:SAMPle:CURR ent Command ..................................................................................... B-18B.68 [SOURce :]LIST:SAMPle: VOLTage Command...................................................................................... B-18B.69 [SOURce:]LIST:SAMPle ? Query ........................................................................................................... B-18B.70 [SOURce :]LIST:SET:SAMPle Command .............................................................................................. B-18
PreviousNext |