KEPCO BOP-MG Operator's Manual

Contents

KEPCO BOP-MG Operator's Manual Manual pdf 18 page image

LIST OF FIGURESFIGURE TITLE PAGEviii BOP-1K 0319121-1 High Power BOP Series Power Supply......................................................................................................... x1-2 1000W BOP Power Supply, Outline Drawing............................................................................................. 1-121-3 BOP Output Characteristics ....................................................................................................................... 1-172-1 BOP Series Rear Panel.............................................................................................................................. 2-12-2 Load Connections, Local Sensing.............................................................................................................. 2-122-3 Load Connections, Remote Sensing.......................................................................................................... 2-122-4 Parallel Configuration, Local Sensing, Typical ........................................................................................... 2-152-5 Parallel Configuration, Remote Sensing, Typical ....................................................................................... 2-162-6 Series Configuration, Local Sensing, Typical............................................................................................. 2-172-7 Series Configuration, Remote Sensing, Typical......................................................................................... 2-182-8 Typical Master/Slave Protection Interconnections ..................................................................................... 2-192-9 Master Power Up Screen ........................................................................................................................... 2-212-10 Power On Default Screen for Master Unit .................................................................................................. 2-222-11 Power On Default Screen for Slave Unit .................................................................................................... 2-232-12 3 x 2 (3 Series X 2 Parallel) Configuration, Local Sensing, Typical ........................................................... 2-253-1 BOP Series Front Panel ............................................................................................................................. 3-13-2 Front Panel Keypad.................................................................................................................................... 3-23-3 Power-up Screen Showing Graphic Meters ............................................................................................... 3-43-4 Power-up Screen Showing Time Line Graph ............................................................................................. 3-43-5 Password Protection Menu, Factory Defaults ............................................................................................ 3-93-6 General Setup Menu .................................................................................................................................. 3-153-7 Max/Min Settings Menu.............................................................................................................................. 3-153-8 Saved Setups Menu ................................................................................................................................... 3-253-9 Saved Waveforms Menu ............................................................................................................................ 3-273-10 Waveform Settings Menu ........................................................................................................................... 3-293-11 Sample Waveform...................................................................................................................................... 3-333-12 Remote Shutdown Using External Power, Standalone or Multiple units.................................................... 3-383-13 Remote Shutdown Using Internal Power, Standalone Units ...................................................................... 3-383-14 Remote Shutdown Using Internal Power, Multiple Units,........................................................................... 3-383-15 Remote Standby, Standalone or Multiple Units.......................................................................................... 3-393-16 Programming Example to Verify Previous Command has Completed....................................................... 3-453-17 RS 232 Implementation.............................................................................................................................. 3-523-18 Tree Diagram of SCPI Commands Used with BOP Power Supply ............................................................ 3-563-19 Message Structure ..................................................................................................................................... 3-603-20 Status Reporting Structure ......................................................................................................................... 3-643-21 Typical Example Of BOP Power Supply Program Using SCPI Commands............................................... 3-654-1 Calibration Setup for Voltage Mode ........................................................................................................... 4-54-2 Calibration Setup for Current Mode............................................................................................................ 4-84-3 Main Calibration Screen ............................................................................................................................. 4-11A-1 GPIB Commands ....................................................................................................................................... A-3B-1 Programming the Output ............................................................................................................................ B-3B-2 Using List Commands to measure sample at End of Pulse ....................................................................... B-5B-3 Using List Commands to measure sample at Start of Pulse ...................................................................... B-6B-4 Setting Limits.............................................................................................................................................. B-8B-5 Using LIST Commands and Queries.......................................................................................................... B-13B-6 Using List:WAIT Commands to Control Generation of a Waveform Measured byMultiple External Devices using a Single External Pulse ........................................................................ B-20B-7 Using List:WAIT Commands to allow an external device time tofunction while imposing a maximum wait time......................................................................................... B-21B-8 Using List:WAIT Commands to Control Generation of a Waveform Measured byMultiple External Devices using the Low-Going leading Edge of an External Pulse ............................... B-24B-9 Using PROT:LIM:POS and PROT:LIM:POS Commands to Set Asymmetrical Limits ............................... B-27B-10 Using Status Commands and Queries ....................................................................................................... B-31B-11 Setting the Unit to Remote Mode via Serial (RS 232) Port ........................................................................ B-34B-12 Using System Commands and Queries ..................................................................................................... B-35