Menu
Panasonic EBL512 manuals
EBL512
Table of contents
- operating instructions
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Introduction
- Definitions / Explanations
- Addressable
- BS4 loop
- External Indicator (LED)
- Overview
- S/W versions
- TLON Manager
- Control Unit
- LED indicators and push buttons
- Normal operation
- The LCD information priority order
- Access levels
- Access level 0
- Access level 2
- Access level 3
- Access level 4
- Silence Alarm devices
- New Zealand FB Silence switch (outside switch)
- Disable / Re-enable alarm devices
- Silence buzzer
- Buzzer
- ventilation outputs
- Evacuate
- Door open
- Technical number / Presentation number
- Technical number for BS4 loop units
- Presentation number
- Alarm types
- Fire alarm
- Fire alarm type A and B
- Alert Annunciation (AA alarm)
- Co-incidence alarm (2-zone / address dependence)
- Key cabinet alarm
- Key cabinet alarm, DBI convention
- Alarm reset
- Single encapsulated reset
- Heavy smoke / heat alarm reset
- Acknowledged alarm
- Fault
- Fault messages
- Fault acknowledge
- Commissioning an installation
- TLON network installation
- Add a Control Unit in a TLON network
- Programming (SSD download)
- Single Control Unit
- User definable text messages download
- New system program (S/W) version download
- Control Units in a TLON network
- EBL512 settings download
- Restart
- Boot menu
- Access
- Perform monthly test (H1)
- Disable or re-enable (H2)
- Disable zone (H2/B1)
- Disable zone / address (H2/B2)
- Disable control output (H2/B3)
- Re-enable zone (H2/B4)
- Re-enable zone / address (H2/B5)
- Re-enable control output (H2/B6)
- Re-enable non-reset zone / address (H2/B7)
- Disable / Re-enable alarm devices (H2/B9)
- Set calendar and clock (H3)
- Daylight saving time
- Disablement (H4/U1)
- Disablement by time channel (H4/U2)
- Doors open (H4/U3)
- Activated 2-zone/address dependent zone/address (H4/U4)
- Sensor values (H4/U5)
- Reset of a week average sensor value
- Algorithm setting via menu H4/U5
- Sensors activating SERVICE signal (H4/U6)
- Event log (H4/U7)
- Configuration (H4/U8)
- Service (H5)
- Access code for service (H5)
- Calibration of supervised outputs (H5/A1)
- Sensitive fault detection mode (H5/A2)
- Direction for communication on COM-/BS4-loop (H5/A3)
- Show information about Site Specific Data (H5/A4)
- Display current consumption in unit (H5/A5)
- Display current consumption COM-/BS4-loop (H5/A6)
- Display statistics for COM-loop (H5/A7)
- Select unit on COM-loop to use for trigging (H5/A8)
- Activate address setting mode for DU (H5/A9)
- Change access code for PC-communication (H5/A10)
- Change access code for service (H5/A11)
- Acknowledge FAULTS (H6)
- Perform ZONE TEST (test mode) (H7)
- Maintenance (H8)
- Disable or re-enable outputs for routing equipment (H8/S1)
- Disconnect loop (H8/S2)
- Re-connect loop (H8/S3)
- Acknowledge SERVICE signal (H8/S4)
- Clear weekly average (H8/S5)
- De-activate alert annunciation function (H8/S6)
- Test alarm devices (H8/S7)
- Safe shut down of control unit (H8/S8)
- Activate address in alarm mode (H8/S9)
- Synchronize the control units (H8/S10)
- Change access code for maintenance (H8/S11)
- Interlocking outputs and inputs (H9)
- Activate interlocking output (H9/C2)
- Reset interlocking output (H9/C3)
- Disable interlocking output (H9/C4)
- Re-enable interlocking output (H9/C5)
- Change access code for daily duties (H10)
- Annual control
- How to change paper in the printer
- board
- Battery maintenance
- How to avoid unnecessary (nuisance) fire alarms
- revision history
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved