Honeywell GX-Series Installation And Setup Manual

Contents

Honeywell GX-Series Installation And Setup Manual Manual pdf 195 page image

GX-Series Control Panel Installation and Setup GuideD-1Appendix D: Event Log MessagesKEYPAD TEXT DESCRIPTIONTRIGGEREVENT0001 + CU-BATT Control Unit Standby Battery Low has occurred (battery voltage below10.2VDC).13. Elec Status20. FaultM0001 - CU-BATT Control Unit Standby Battery Low has finished (battery voltage now above10.2VDC).13. Elec. Status M0002 + CU-AC Control Unit Mains (a.c.) Power Fail has occurred. 13. Elec. Status20. FaultM0002 - CU-AC Control Unit Mains (a.c.) Power Fail has finished. 13. Elec. Status M0003 + LID TAMP Lid Tamper on control unit has occurred. 9. Tamper M0003 - LID TAMP Lid Tamper on control unit has finished. 18. Zone restoral M0004 + AUX TAMP Auxiliary Tamper on control unit has occurred. 9. Tamper M0004 - AUX TAMP Auxiliary Tamper on control unit has finished. 9. Tamper18. Zone restoralM+ABORT SET Setting process aborted 11. Reset NM+AC+BATT AC Fail and battery voltage low. 13. Elec. Status20. FaultM+ AC FAIL AC Fail zone activated (opened) or an AC Fail on a Power Supply Unit. 13. Elec. Status20. FaultM– AC FAIL AC Fail zone de-activated (closed) or an AC Fail on a Power Supply Unit hasstopped.13. Elec. Status20. FaultM+ALARM EXT Alarm extend zone activated. 3. 24 Hours16. Log ZoneMALM CAUSE Reset of system required by entry of an alarm cause code. Always TR MADDED Engineer has added a Module to the system. 9. Tamper MARC TEST Alarm Receiving Centre Test Always TR NM+ATM-1 ATM-1 zone activated. 3. 24 Hours16. Log ZoneNM+ATM-2 ATM-2 zone activated. 3. 24 Hours16. Log ZoneNM+ATM-3 ATM-3 zone activated. 3. 24 Hours16. Log ZoneNM+ATM-4 ATM-4 zone activated. 3. 24 Hours16. Log ZoneNMAUTOTEST Automatic Test of the system via a comms Module Always TR+AUTOTIMER Autoset timer activated. None NM–AUTOTIMER Autoset timer de-activated. None NMBURG HIGH High priority intruder alarm zone open 2. Intrude18. Zone RestoralMBURG LOW Low priority intruder alarm zone open. 2. Intrude18. Zone RestoralM+BAT FUSE ◊ Fault on battery protection 13. Elec Status20. FaultM+ BATT LOW Battery Low activated on Power Supply Unit. 13. Elec. Status20. FaultM– BATT LOW Battery Low de-activated on Power Supply Unit. 13. Elec. Status20. FaultM+BEAM PAIR Beam Pair zones activated (opened). 2. Intruder NM+BEGIN SET Setting process started. None NM+ BELL FAIL Bell Fail zone opened. 16. Log Zone NM+ BELL TAMP Bell Tamper zone activated (opened). 9. Tamper M– BELL TAMP Bell Tamper zone de-activated (closed). 9. Tamper18. Zone restoralMBOOT UP System has been started up or restarted. 13. Elec. status NMCANCEL Alarm activation Cancelled by a valid user Code (system or Group(s) still Set). 11. Reset/Cancel NMCOMM FAIL Communication Failure has occurred on a comms Module. 20. Fault MCONFIRM Two independent alarms. 2. Intruder MCOPY SITE Remote Copy of the Site (system) has occurred via Remote Servicing or theRS232 Module.None NMCUSTOM- Custom-A zone activated (opened). 5. Custom zones16. Log ZoneNMCUSTOM-B Custom-B zone activated (opened). 5. Custom Zones16. Log ZoneNM+CU-FUSE ◊ Control Unit protection trouble. 9. Tamper13. Elec Status20. FaultMDELAY ALM PA Delay Alarm zone activated after PA Delay timeout. 1. PA/duress M◊ The PC board uses a PTC device instead of a fuse. The PTC serves as an automatically resetting fuse.