Honeywell GX-Series Installation And Setup Manual

Contents

Honeywell GX-Series Installation And Setup Manual Manual pdf 196 page image

GX-Series Control Panel Installation and Setup GuideD-2KEYPAD TEXT DESCRIPTIONTRIGGEREVENTDL/SL ALM PA Delayed Silent zone activated after PA Delay timeout. 1. PA/duress MDOOR PROP MAX - Door left open 4. Security NMDR MASKED Detector Masked. Activity Monitoring of zone has failed. 15. Trouble20. FaultDUAL Dual (Double Knock) zone activated (opened). 2. Intruder MDURESS Duress code has been entered 1. PA/Duress MENG ASSEM Engineering Assemble Zone Menu (Menu Option 64) has been accessed. 14. Menu Access MENG CHECK Engineering Pre-Check Menu (Menu Option 66) has been accessed. 14. Menu Access MENG DIAG Engineering Diagnostics Menu (Menu Option 61) has been accessed. 14. Menu Access MENG DIGI Engineering Digicom (Communications) (Menu Option 56) has been accessed. 14. Menu Access MENG GROUP Engineering Groups (Menu Option 63) has been accessed. 14. Menu Access MENG KPAD Engineering Keypad (Menu Option 58) has been accessed. 14. Menu Access MENG LINKS Engineering Links (Menu Option 54) has been accessed. 14. Menu Access MENG O/PS Engineering Outputs (Menu Option 53) has been accessed. 14. Menu Access MENG PARAM Engineering Parameters (Menu Option 51) has been accessed. 14. Menu Access MENG PRINT Engineering Print (Menu Option 57) has been accessed. 14. Menu Access MENG QUICK Engineering Quick Menu (Menu Option 59) has been accessed. 14. Menu Access MENG SOAK Engineering Soak Test (Menu Option 55) has been accessed 14. Menu Access MENG TEST Engineer Test of the system via the Telecom Module. Always TR NMENG TMRS Engineering Timers A/B (Menu Option 65) has been accessed. 14. Menu Access MENG ZONES Engineering Zones (Menu Option 52) has been accessed. 14. Menu Access MENG TAMP Tamper when entering Engineer Mode. None NM+ENGINEER Entering Engineer Mode. Always TR NM–ENGINEER Leaving Engineer Mode. Always TR NMENT DELAY User entering Ent Delay State None NMENT SET User entering Ent Set State None NMENT SETNG User entering Setting State None NMENT UNSET User entering Unset State None NMENT UNST User entering Unsetting (disarming) State None NM+ENTRY Entry zone activated (opened) during Setting/Unsetting (arming/disarming)procedure or when Set.None NM–ENTRY Entry zone de-activated (closed) during Setting/Unsetting (arming/disarming)procedure or when Set.None NMETST FAIL Engineer test has failed None NMETST PASS Engineer test has passed None NM+EXIT Exit zone activated (opened) during the Unsetting (disarming) procedure orwhen Set.2. Intruder NM–EXIT Exit zone de-activated (closed) during the Unsetting (disarming) procedure orwhen Set.2. Intruder NMEXITGUARD ExitGuard zone activated (opened). 16. Log NMEXTENSION System or Group(s) are in the Autoset Extension period. 10. Setting NMFAIL SET Fail to set event. 7. Set Fault M+FAULT Fault condition activated on zone 20. Fault M–FAULT Fault condition cleared from zone 20. Fault MFAULT RST Fault has been cleared 20. Fault NMFB BAT LOW RF Fob has low battery None NM+FINAL Finalzone activated (opened) during Setting/Unsetting (arming/disarming)procedure or when Set.7. Set Fault NM–FINAL Final zone de-activated (closed) during Setting/Unsetting (arming/disarming)procedure or when Set.7. Set Fault NMFIRE Fire zone activated (opened). 6. Fire MFOB REJCT Illegal fob None MFORCE OMT Force Omit of a zone (Menu Option 14). 8. Omit MFULL SET Full Set (Menu Option 12) of the system or Group(s). 10. Setting MFULL TEST Full Test (Menu Option 62) has occurred. None NMFUSE 14.5 ◊ Fault with 14.5V protection on Power Supply Unit 13. Elec. Status20. FaultMFUSE AUX1 ◊ Fault with AUX1 protection on Power Supply Unit 9. Tamper13. Elec. FaultMFUSE AUX2 ◊ Fault with AUX2 protection on Power Supply Unit 9. Tamper13. Elec. StatusMFUSE BELL ◊ Change fuse to protection. 9. Tamper13. Elec. StatusM+GRP OMIT Area bypass has occurred (Group(s) has been omitted). 8. Omit M–GRP OMIT Group omit/area bypass has finished (Group(s) has been un-omitted). 8. Omit M+HIGH RES Zone changing to High Resistance (1200 to 1300 Ohm) Engineer Log only. 15. Trouble M◊ The PC board uses a PTC device instead of a fuse. The PTC serves as an automatically resetting fuse.