Panasonic AJ-HD1400E Operating Instructions Manual

Also see for AJ-HD1400E: Mechanical Parts List

Panasonic AJ-HD1400E Operating Instructions Manual Manual pdf 61 page image

61Error messages (continued)Displaying the warning informationz A warning message appears when a warning has occurred. “NO WARNING” appears when a warning has not occurred.z When more than one warning has occurred simultaneously, move the joystick up or down to check the description of eachwarning.*1 This error message always appears in the EE mode.In such a case, black signals are recorded as the video signals, and the audio signals are muted.*2: This error message always appears in the EE mode.In such a case, the audio signals are muted.*3: This error message always appears in the EE mode.In such a case, the time code of the time code generator inside this unit is recorded as the time code signal.Warning messagesPriority Monitor display Description Corrective action VTR operationHighE-20(DEW)If condensation is detected, the error number flashes andthe unit transfers to eject mode. The drum rotates afterthe cassette is ejected to eliminate the condensation.Once the unit is released from condensation status, theerror message display is cleared and the VTR is able tobe used.z If condensation is detected in the eject mode, the drumstarts rotating as soon as it is detected.z If condensation is detected when the cassette hasbeen inserted, the drum rotation is stopped, and afterthe tape is ejected, the drum starts rotating.Leave the power on and wait. EJECTE-95(INVALIDEMBEDDED TC)(When “SLTC” is selected in menu No. 032 REC REF)Appear when a time code for a signal input into the HDSDI IN connector is not stepping at the standard rate insynchronizing the image frames to be recorded with thetime code.Check the time codeinformation of the input signal.Operationcontinues.E-92(1394 INITIALERROR)Display if the IEEE1394 digital interface connection statusis irregularIf the cable connection is inloop status, reconnect to 1 to1.If not using the loopconnection, turn the POWERswitch OFF > ON.Signal inputand outputthrough theIEEE1394digital interfaceis stopped.E-04(UNKNOWN SIG)This appears when the signals supplied from theIEEE1394 digital interface are not DVCPRO/DV formatsignals.Check that the 1394 input hasbeen connected properly.No recording operations arepossible.E-90(NOT 1X 100M SIG)This appears when the initialization process fails duringcommunication via the IEEE1394 digital interface. Check the input signal. Operationcontinues.* 1E-16(INVALID VIDEOSIG)This appears when the compressed video signalssupplied from the IEEE1394 digital interface are irregularsignals.z This warning appears only during recording operations.In such cases, no signals are recorded on the tape,and only erasure of existing signals is performed.Check the 1394 input signals.Itis possible that playbacksignals of an unrecorded tapeare being input.Operationcontinues.* 1E-17(INVALID AUDIOSIG)This appears when the audio signals supplied from theIEEE1394 digital interface are irregular signals.z This warning appears only during recording operations.In such cases, the signals are recorded with the audiosignals muted.Check the 1394 input signals.Itis possible that signals otherthan 1x playback signals arebeing input from a VTR orother device.Operationcontinues.* 2E-18(INVALID TC SIG)This appears when the time code information suppliedfrom the IEEE1394 digital interface is irregularinformation.z This warning appears only during recording operations.In such cases, the internally generated time code isrecorded.Check the time code of thedevice which is supplying thetime code.Operationcontinues.* 3E-14(NO MATCH SIG)This appears when the signals supplied to the IEEE1394digital interface are at variance from the system formatwhich is set by this unit.Check the input signal. Operationcontinues.* 1E-10(FAN STOP)This appears when the fan motor has shut down.z The power automatically turns off if 5 minutes pass withthe fan stopped.Check the fan for foreignmatter.Operationcontinues.E-09(NO RF)This appears when a blank section lasting for more thanone second on the tape has been detected duringplayback.A blank section is identified as such when all the followingconditions are met:z There are no output signals from any of the heads.z The playback data cannot be read.z There is no CTL signal (DV/DVCAM tapes excluded).Check the tape. It is possiblethat an unrecorded tape hasbeen loaded.Operationcontinues.