10Parts and their functions (continued)Front panel (2)INPUT SELECT buttonsThese buttons are used to switch the video and audioinput signals. They can also be used to switch the videoinput signals to the internal reference signal selected asthe menu item No.601 VIDEO INT SG setting.VIDEO:Each time the VIDEO button is pressed, the inputvideo signal selection is switched in the order of[HD SDI] > [1394] > [SG].When SG has been selected, the signal is switched tothe internal reference signal selected as the menu itemNo.601 VIDEO INT SG setting.AUDIO:Each time the AUDIO button is pressed, the inputaudio signal selection is switched in the order of[HD SDI] > [SG] > [ANALOG].z It is possible to inhibit the input switch operations(video and audio) of the INPUT SELECT buttonsusing menu item No.190 V IN SEL INH and itemNo.191 A IN SEL INH.z The audio input signal cannot be switched to [1394]independently. The audio signal can be switched to[1394] only when the video signal is switched to[1394] by interlocking.Since the audio input signal at this time is fixed to[1394], it cannot be switched to another input signal.PF buttonWhen this button is pressed, buttons - tofunction as the PF1, PF2 and PF3 buttons, respectively.When it is pressed again before another button ispressed, these modes are canceled.When this button is pressed together with the MENU/DIAG button , the DIAG screen is displayed.COUNTER/PF1 buttonEach time this button is pressed, the counter display onthe display panel changes by one step in the followingsequence: CTL > TC > UB > REM.RESET/PF2 buttonWhen this button is pressed in the CTL mode, thecounter display is reset to [00:00:00:00].When it is pressed in the TC/UB mode while holdingdown the TC PRESET button , the generator is reset.TC PRESET/PF3 buttonThis button is used to set the TC or UB values.MENU/DIAG buttonWhen the connector that is selected in menu No. 005SUPER is used, When this button is pressed, the setupmenus are displayed on the TV monitor, and the setupmenu numbers are displayed on the unit’s display panel.When it is pressed again, the setup menu settings areexited, and the original status is restored.When the button is pressed while holding down the PFbutton , the VTR information is displayed. When it ispressed again, the original display is restored. The VTRinformation consists of the WARNING, HOURS METER,UMID INFO and DIF STATUS 1, 2 information.The SEARCH button is used to switch the displaysbetween these kinds of information.Descriptions of the warnings are displayed on theWARNING screen. The deck’s serial number, powerontime, drum rotation time, tape travel time, number ofloading times, number of power on/off times, etc. aredisplayed on the HOURS METER screen. The UMID(Unique Material Identifier) information is displayed onthe UMID INFO screen. The IEEE1394 digital interfaceinformation is displayed on the DIF STATUS 1, 2 screen.TCG switchREGEN: The internal time code generator issynchronized with the time code which the timecode reader has read from the tape.The signal that is to be used for regeneration isselected using menu No. 505 TCG REGEN.PRESET: The time code generator can be preset (seepage 55) on the operation panel or by remotecontrol.EXT: The external time code which is input from thetime code input connector or video signal SLTC,SVITC or IEEE1394 digital input signal is used.Which of the two is to be set is selected usingmenu No. 507 EXT TC SEL.When selecting “1394” with the INPUT VIDEO switch onthe front panel, the time code input to IEEE1394 digitalinput/output connector is used.SUPER switchON: Outputs superimposed information, such as timecode, to the connector selected in menu No. 005SUPER.OFF: No superimposed information is output.REC/PBCH1/5 CH2/6 CH3/7 CH4/8RECPBCH1 CH2 CH1 CH2PBHDSEARCHbutton
