ADEMCO Vista-32FB Installation And Setup Manual

Also see for VISTA-32FB: User guide Quick start guide Installation and setup guide Installation and setup user's guide Programming guide

Contents

ADEMCO Vista-32FB Installation And Setup Manual Manual pdf 63 page image

Section 5 – Data Field Descriptions5-3FIELD TITLE and DATA ENTRIES EXPLANATION077280 Power-Up in Previous State0 = disable1 = enableIf enabled, the system, upon power-up, reverts to its status prior to a completepower loss.If disabled, the system always powers up in a disarmed state.NOTE: Neither authority level 0 nor 5 can be used to disarm the system if thecontrol powers up armed.Must be 1 for UL applications.077290 Quick Arm (partition-specific)0 = disable1 = enableIf enabled, allows arming of the burglary system in AWAY, STAY, INSTANT,or MAXIMUM mode by using the [#] key instead of the user code.NOTES:When armed, the system reports closing as User 0 if Open/Close reporting forUser #2 (typically a Master level user) was enabled for a given partition.If Quick Arm is used, the Installer Code and Authority Level 5 codes cannotdisarm the system.Main Dialer TouchTone or RotaryDial0 = rotary1 = touchtoneSelect the dialing method for the main dialer.If you select TouchTone, make sure the subscriber has requested and is paying for TouchTone service. Note thatwhether or not TouchTone dialing for call placement is permitted, communication by the use of DTMF signaling(ADEMCO High Speed) will still take place. See field 1*33 for TouchTone w/Rotary backup077300077310 PABX Access CodeEnter 00-09; B-F (11-15)This field is used to enter up to four 2-digit numbers representing the prefixneeded to obtain an outside telco line. If not required, enter nothing andproceed to next field.077320 Primary Subscriber’s AccountNumber (partition-specific)Enter 00-09; B-F (11-15)Enter a 3- or 4-digit (depending on report format) primary subscriber accountnumber. Each number requires a 2-digit entry so as to allow entry ofhexadecimal digits (B-F). If a 3-digit account number is to be used, enter dataonly in the first 3 locations, and enter * in the fourth location.077330 Primary Phone NumberEnter 0-9; #11 for *, #12 for #, #13 for a 2-second pause.Enter the primary central station phone number, up to 17 digits. This is thephone number the control will use to transmit Alarm and status messages tothe central station. Do not fill unused spaces.NOTE: Backup reporting is automatic only if a secondary phone number isentered.077340 Secondary Phone NumberEnter 0-9; #11 for *, #12 for #, #13 for a 2-second pause.Enter the secondary phone number, up to 17 digits. The secondary phonenumber is used if communication on the primary number is unsuccessful, or ifsplit/dual reporting is desired. Do not fill unused spaces.NOTE: If this field is programmed, a secondary subscriber account number(field *90)must also be programmed.077350 Download Phone NumberEnter 0-9; #11 for *, #12 for #, #13 for a 2-second pause.Enter the downloading phone number, up to 17 digits. Do not fill unusedspaces.NOTE: This field is applicable only if downloading is utilized.077360 Download ID NumberMake entries as 2-digit numbers as follows:00=0 01=1 02=2 03=3 04=4 05=506=6 07=7 08=8 09=9 10=A 11=B12=C 13=D 14=E 15=FEnter eight digits.NOTE: This field is applicable only if downloading is utilized.077370 Download Command Enables0 = disable1 = enableEnabling a function means that you are able to perform that function via theADEMCO Compass Downloading software.Functions are as follows: Dialer Shutdown; System Shutdown; Not Used;Remote Bypass; Remote Disarm; Remote Arm; Upload Program; DownloadProgram.For UL commercial burglary and fire installations, all entries must be 0.