ADEMCO Vista-32FB Installation And Setup Manual

Also see for VISTA-32FB: User guide Quick start guide Installation and setup guide Installation and setup user's guide Programming guide

Contents

ADEMCO Vista-32FB Installation And Setup Manual Manual pdf 38 page image

VISTA-32FB/VISTA-128FB Installation and Setup Guide3-22Installing the 4100APG Pager InterfaceWhenever an event occurs on the VISTA-32FB/VISTA-128FB, a message can be sent to a pager. This isaccomplished by using the 4100APG Pager Interface.The 4100APG will dial and send the information to apaging service. It will transmit to the pager anymessage programmed to be sent to the event logprinter, even if the printer is not being used.The types of messages are divided into 6 categories:Alarms; Troubles; Bypasses; Opens/Closes; System andTest. The VISTA-128FB can be programmed so eachtype of message transmits to a different pager. Eachtype has its own programming field for the pager phonenumber and pager ID. Of course, these could be sent tothe same pager by programming those fields with thesame pager phone number and ID.The 4100APG will hang up between each message.Multiple messages will be sent in the order received. Ifthe 4100APG cannot make contact with the pagingservice, it will retry up to 10 times. If the interfaceloses contact with the VISTA-32FB/VISTA-128FB, itwill send a message to the paging service to notify theuser.The pager interface must be wired to a differentphone line than the VISTA-32FB/VISTA-128FBitself. Otherwise, the communication of bothwill not function properly.4100APG LED IndicationsBelow is a table outlining the LED indications:LED Steady Blinking Off PulsePower OK On Battery(B/U)NoPowerLine Not in use (OK) In UseCall Call in Progress Page Retry IdleBusy Telephone Busy No Dial Tone OKPage Page Fail OK Page OKData No Data Msg DataLoad No Data Prog DataTRBL Trouble OKMounting the 4100APGThe 4100APG may be mounted in the control cabinet ifspace is available or, if this is not possible, on the sideof the cabinet or adjacent to it. Pry off the pagerinterface’s cover prior to wiring.To mount the 4100APG, perform the following steps:Step Action1 When the 4100APG is mounted inside thecontrol cabinet, attach it to the cabinet'sinterior surface with 2-faced adhesive tape.You may leave the interface's cover off if it ismounted within the cabinet.2 When the 4100APG is to be mounted outsidethe cabinet, use the screw holes at the rearto mount horizontally or vertically (2-facedadhesive tape may be used, if preferred).You can bring wires out from the side orback (a round breakout is also available onthe back). .Do not mount the 4100APG on the cabinetdoor or attempt to attach it to the PC board.Wiring the 4100APG Without the Event Log PrinterThe 4100APG connects to the VISTA-32FB/VISTA-128FB via the 4100SM. The 4100SM wires to the J2connector on the control via the 4142TR Cable. SeeFigure 3-26.To mount the 4100APG, perform the following steps:Step Action1 Connect the 4142TR to J2 on the control.2 Connect the Red and Violet wires of 4142TRto TB1-6 (RxD) and TB1-1 (DTR) of 4100SM,respectively.3 Connect TB1-7 and TB1-8 of 4100SM toterminal 12 (Aux. Power -) and terminal 11(Aux. Power +) of the control, respectively.4 Connect the incoming telephone line to the4100APG RJ11 connector labeled LINE.(Optional) Connect the handset side oftelephone line to 4100APG RJ11 connectorlabeled PHONE5 Connect the DB25M to DB-9M Cable(supplied), from 4100SM (25 pin) to4100APG (9 pin) connector labeled SERIALPORT INPUT6 When you complete the module's mountingand wiring, you should install the module'scover (with label affixed, as indicated next).