Panasonic WV-CW970 Operating Instructions Manual

Also see for Super Dynamic III WV-CW974: Product catalog Product catalog Brochure & specs Specifications Operating instructions

Contents

Panasonic WV-CW970 Operating Instructions Manual Manual pdf 26 page image

-26-2. Move the cursor to →PUSH SET to the right ofPAN/TILT, and then press the CAM (SET) button todisplay the PAN/TILT setting menu.3. Use the joystick to position the camera, and thenpress the CAM (SET) button.4. Move the cursor to → PUSH SET to the right ofZOOM/FOCUS, and then press the CAM (SET)button to display the ZOOM/FOCUS setting menu.5. Move the joystick left, right, up and down to adjustthe position of the lens focus, and then press theCAM (SET) button.Notes:• Focusing may be difficult, because of the distortioncaused by the curve of the dome cover, when thecamera is at an angle that is close to horizontal.• A different position number can be selected by movingthe cursor to the position number at the top of theposition setting menu and tilting the joystick left andright. Pressing the CAM (SET) button will change to thesetting screen for the newly selected position number.• The currently registered camera ID and preset IDappear at the bottom of the position setting menu.• When using a system device other than the WV-CU650/CU950*, WJ-HD309A/HD316A over 65position numbers cannot be set. (as of September2005)* Operation procedure may vary depending onthe version of the system controller's software.For Ver.1.xx or earlier: only camera functionoperations are supportedFor Ver.2.xx or later: PRESET/PGM PRESETbutton is also supported● Adjusting Camera Position WhenChanging Cameras (PAN OFFSET SET)The system controller etc. has a function fordownloading (saving) and uploading (recovering)setting information for the camera. This function allowsyou to upload (recover) original setting information thathas been downloaded (saved) before someunforeseen damage or malfunction causes settinginformation in the camera to be lost. However, theremay be some slight differences in images from thoseuploaded (recovered) when the camera is changed.The "PAN OFFSET SET" function is for adjusting thesedifferences.1. Align the cursor with "PAN OFFSET SET" with the ←or → arrow, and press the CAM (SET) button to setthe offset value.Set the offset value to 0.0, or in a range of -10 to+10. All preset positions for the camera's positionare adjusted according to the offset value.Important: Data is not compatible with existingcameras. Uploading setting information fromexisting cameras will damage data in the camera. Ifdata in the camera is damaged, download camerasetting information from a camera that still has thefactory settings and then upload it to the camerawith the damaged data.● Preset ID Setting (PRESET ID)The preset ID is a series of alphanumeric charactersthat indicate the location of the camera. This item canbe used to turn display of the preset ID on the monitorscreen on or off, and to input the preset ID.1. Move the cursor to PRESET ID, and then tilt thejoystick left or right to toggle preset ID display onand off.2. Select ON or OFF, and then press the CAM (SET)button.This will display the preset ID setting menu.→PUSH SET** POSITION 1 **PAN/TILTZOOM/FOCUSPAN OFFSET SET ← 0 →RET TOPFLOOR1DOOR→PUSH SET→PUSH SET→PUSH SET** POSITION 1 **PAN/TILTZOOM/FOCUSU TILT D/L PAN RPAN OFFSET SET ← 0 →RET TOPFLOOR1DOORPRESET NO. 1*POSITION SETPRESET IDRET TOP DELON→PUSH SET→PUSH SET** POSITION 1* **PAN/TILTZOOM/FOCUSPAN OFFSET SET ← 0 →RET TOPFLOOR1DOORAlign the cursor here→PUSH SET→PUSH SET** POSITION 1 **PAN/TILTZOOM/FOCUSU ZOOM D/L FOCUS RPAN OFFSET SET ← 0 →RET TOPFLOOR1DOOR