JVC CX-7000 Series Electronic Manual

Bend Remedyv Displays the bend remedy mode settings.Settingsv Temp Level: -5, -4, -3, -2, -1, 0, OffFor setting the bend remedy heating roller temperature.Selecting a larger value increases the temperature.If the printer is not reset after changing the temperature setting,temperature is adjusted after the printing operation starts.v Speed: -2, -1, 0, 1, 2For setting the bend remedy speed.Selecting a larger value increases the speed.Heat Rollerv Displays the settings of the Power Saving mode or HR Controlmode.Settingsv Power Saving: 5, 10, 15, 20, 25, 30, 45, 60, Off (unit: mins)For setting the time for the Power Saving mode.While in the [Ready] mode, if the printer is not operated for a specifictime interval, the retransfer heating roller, bend remedy heatingroller, and backlight of the operation panel will turn off automaticallyto save power.While in the Power Saving mode, [Sleeping..] is displayed.To cancel the setting temporarily using the operation panel, pressKNB to reset the printer.v HR Control: Off, OnFor setting whether to standby the printer by lowering the retransferheating roller temperature if cards are not printed for 30 minutes orlonger.The printer will automatically be restored to the original mode duringthe next card printing, but it may take a longer time before the firstcard is printed. Set this to [On] during normal use.Settingv Displays the printer settings.v Setting can also be performed using the printer’s operation panel.Settingsv Display:Mode: Counter, Laminator StateThis is used for setting the information to be displayed on theoperation panel."Display Mode Setting" (A page 25)Counter: Total Cnt, Head Cnt, Free Cnt, Cleaning Cnt, Error CntThis is used for setting the type of counter displayed on theoperation panel."Counter Setting" (A page 25)Contrast: -3, -2, -1, 0, 1, 2, 3For setting the contrast of the operation panel display."Contrast Setting" (A page 27)v Buzzer: On, OffFor setting whether to sound the buzzer when an error occurs orwhen settings are changed."Buzzer Setting" (A page 28)v Unit No.:No.1 - No.10For setting the printer’s unit number according to the USBenvironment."Unit Number Setting" (A page 28)Optionv Displays the optional settings.Settingsv MG: None, ISODisplays the availability of a magnetic encoder or the type ofmagnetic encoder used.v IC Antenna: None, InstalledDisplays the availability of a non-contact IC encoder.v IC Contact: None, ISO TypeDisplays the availability of a contact IC encoder (contact section) orthe type of IC encoder used.v Contact IC R/W: None, InstalledDisplays the availability of a contact IC R/W.v Bend Remedy HR: None, InstalledDisplays the availability of a bend remedy unit.v Turn Over: None, InstalledDisplays the availability of a card turn over unit.MGv Displays the magnetic encoder settings.Settingsv ISO Type: Loco, HicoFor setting the coercivity when writing data to an ISO magnetic stripecard.v Retry Count: 0, 1, 2, 3For setting the maximum number of retries when writing to orreading of the magnetic stripe fails.Networkv Displays the network settings.Settingsv Printer Name: ASCII character strings (10 characters)For setting the printer name.v Host IF: LAN, USBFor setting the interface.If the printer is connected via USB interface, the setting switchesautomatically to USB when initialization starts even if the LAN settingis selected.v IPv4:DHCP: On, OffSetting: IP Address, Subnet Mask, GatewayEfective IP:IP AddressFor setting IPv4.v IPv6:Adrs Config: Auto, ManualSetting: IP Address, Prefix Len, GatewayEfective IP: IP Address1, IP Address2, IP Address3For setting IPv6.v Session Time Out: Off, 10 mins, 20 mins, 30 mins, 60 minsFor setting the session timeout interval.v MAC Address: Hexadecimal character stringsDisplays the MAC address.v IPSec Mode: Off, OnFor setting the availability of IPSec.v IPSec Type: not Setting, Preshard, CertificateDisplays the method of IPSec authentication.Operating the Printer16