Chapter 1414-1014.5 FAX Error Codes14.5.1 Outline14.5.1.1 Error Code Outline 0017-6044iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iAn error code is used to indicate a fault in a machine, and is indicated in the machine's LCD or reports, showing the nature (symptoms) of the fault. Using the errorcode, the user or the service man can readily find out how to correct the fault by simply referring to the User's Manual or service manual.An error code may be either of the following two types:User Error CodesA fault indicated as a user error code is one that can easily be corrected by the user, as by operating the machine. It takes the form of "#+number."Service Error CodesIf a fault calls for a service man for correction, it is indicated as a service man error code in the form of "##+number" or "SYSTEM ERROR E+number."MemoA service error code expressed in the form of "##+number" will not appear on the LCD, Error Tx Report, or Activity Report while the machine remainsin factory default state. To check a service error code, shift bit 0 of service soft switch #1 SSSW SW01 to '1'.MemoDisplay only the error codes which are newly incorporated in this machine as well as which require remedies unique to the product. For the causes andcountermeasures of other error codes, refer to the separate G3/G4 Facsimile Error Code List (Rev. 2).14.5.2 User Error Code14.5.2.1 User Error Code 0017-6045iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-914.5.3 Service Error Code14.5.3.1 Service Error Code 0017-6046iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-10No. Tx/Rx Description#0001 [Tx] an original has jammed.#0003 [Tx/Rx] tine-out for copying or sending/receiving a single page has occurred.#0005 [Tx/Rx] time-out for initial identification (T0/T1) has occurred.#0009 [Rx] recording paper has jammed or is absent.#0012 [Tx] recording paper is absent at the other party.#0018 [Tx/Rx] auto call initiation has failed.#0037 [Rx] image memory overflow at time of reception has occurred.#0059 [Tx] The number you dial and connected number (CSI) does not match.#0995/0099 [Tx/Rx] a memory communication reservation has been cancelled.No. Tx/Rx Description##0100 [Tx] at time of transmission, the procedural signal has been transmitted more than specified.##0101 [Tx/Rx] the modem speed does not match that of the other party.##0102 [Tx] at time of transmission, fall-back cannot be used.##0103 [Rx] at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).##0104 [Tx] at time of transmission, RTN or PIN is received.##0106 [Rx] at time of reception, the procedural signal is received for 6 sec while in wait for the signal.##0107 [Rx] at time of reception, the transmitting party cannot use fall-back.##0109 [Tx] at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been sentmore than specified.##0111 [Tx/Rx] memory error has occurred.##0114 [Rx] at time of reception, RTN is transmitted.##0200 [Rx] at time of reception, no image carrier is detected for 5 sec.##0201 [Tx/Rx] DCN is received outside the normal parity procedure.##0220 [Tx/Rx] system error (main program out of control) has occurred.##0232 [Tx] encoding error has occurred.##0237 [Rx] decoding error has occurred.##0261 [Tx/Rx] system error has occurred.##0280 [Tx] at time of transmission, the procedural signal has been transmitted more than specified.##0281 [Tx] at time of transmission, the procedural signal has been transmitted more than specified.
