Chapter 1414-514.3 Jam Code14.3.1 Jam Codes (Related to Printer Unit) 0017-6038iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-314.3.2 Jam Codes (Related to Finisher) 0017-6039iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-414.3.3 Jam Codes (Related to ADF) 0017-6040iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iT-14-514.3.4 Jam Codes (Related to Duplex Unit) 0017-6041iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018iCode Name Sensor No. Description0104 Delay jam in paperpickup sectionSR209 The registration sensor cannot detect the leading edge of paper from the moment paper pickup starts to themoment the jam detection time is reached.0208 Stationary jam in paperpickup sectionSR209 The registration sensor cannot detect the no paper status specified time before the leading edge of the pickedup paper reaches this sensor.010c Delay jam in deliversectionSR202,SR203,SR209- The fixing delivery sensor cannot detect presence of paper within the specified time after turning on of theregistration clutch.- The fixing delivery sensor detected absence of paper within the specified time after the sensor had detectedpresence of paper within the specified time after turning on of the registration clutch.- The No.1 delivery sensor cannot detect presence of paper within the specified time after turning on of thefixing delivery sensor.0210 Stationary jam indelivery sectionSR202,SR203- The fixing delivery sensor cannot detect absence of paper within the specified time after turning off of theregistration clutch.- The fixing delivery sensor cannot detect absence of paper within the specified time after the sensor detectedthe leading edge of paper.- The No.1 delivery sensor cannot detect absence of paper within the specified time after the sensor detectedthe leading edge of paper.0214 Stationary jam inmachineSR202,SR203,SR209Paper was detected in the paper transport path during initial rotation, during automatic delivery, at the endof cleaning, or at reception of an emergency stop command.1118 Door open jam SR202,SR203,SR209,SW2, SW3The door was opened when there was printing paper in the transport path.Code Name Sensor No. Description0130 Delayed feed jam PI5 The inlet sensor is not turned on within the specified time after reception of a paper ejection signal fromthe host machine.0231 Staying paper jam PI5 The inlet sensor is not turned off even if paper is fed by the specified distance after the leading edge ofthe paper from the host machine has passed through the sensor.0033 Stack ejection jam PI1 When a paper stack is ejected, the HP sensor is not turned off within the specified time.0035 Staple jam Stapler HPsensor(built instapler)The stapler HP sensor was turned off once after start of stapler operation, but the HP has not been reachedwithin the specified time.1036 Power-on jam PI5 The inlet sensor detected paper at power-on.1137 Door open jam SW1 The front cover switch detected opening of the front cover during standby or copy operation.Code Name Sensor No. Description0000 Unknown jam - Other errors0007 Initial stationary PI6,PI7,PI8 Paper is detected in the transport path before the DADF starts initial operation.0008 Read sensor delay PI7,PI8 The read sensor does not detect paper when the paper has been fed by the predetermined distancesince reception of a pickup request.0009 Read sensor stationary PI7 The trailing edge of paper is not detected when the paper has been fed by the predetermined distancesince detection of it by the read sensor.000a Paper absence (Pull out the document.) PI11 The Document set sensor has been held off since start of pickup.000c Delivery reversal sensor delay PI6,PI7 The delivery reversal sensor does not detect paper since the paper has been fed by the predetermineddistance since the read sensor was turned on.000d Delivery reversal sensor stationary PI6 The trailing edge of paper is not detected when the paper has been fed by the predetermined distancesince the delivery reversal sensor detected the paper.000e ADF cover open PI10 The feeder cover was opened during operation (of the drive system).000f User ADF open sensor ofthe readerunitThe ADF was opened during operation (of the drive system).0010 Pickup NG - The registration sensor has been held off since paper pickup started.
