Siemens SINUMERIK 840Di Diagnostic Manual

Also see for SINUMERIK 810D: Programming manual Programming manual Programming manual Function manual Function manual

Overview of Alarms 11/2006NCK alarms2-66© Siemens AG, 2006. All rights reservedSINUMERIK, SIMODRIVE Diagnostics Manual (DA), 11/2006 Edition6010 Channel %1 data block %2 not or not completely created, error code %3Parameters: %1 = Channel number%2 = String (block name)%3 = Internal error codeDefinitions: The data management has detected an error in power-up. The specified data block may not havebeen created. The error number specifies the type of error. If the error number >100000, then there isa fatal system error. Otherwise, the user memory area was made too small. In this case the (user)error codes have the following meaning:- Error number 1: No memory space available- Error number 2: Maximum possible number of symbols exceeded- Error number 3: Index 1 lies outside the valid value range- Error number 4: Name already exists in channel- Error number 5: Name already exists in NCKIf the alarm occurs after cycle programs, macro definitions or definitions for global user data (GUD)have been introduced, the machine data for the user memory configuration have been incorrectlyconfigured. In all other cases, changes to machine data that are already correct lead to errors in theuser memory configuration.The following block names (2nd parameter) are known in the NCK (all system and user data blocks;in general, only problems in the user data blocks can be remedied by user intervention):- _N_NC_OPT - System internal: option data, NCK global- _N_NC_SEA - System internal: setting data, NCK global- _N_NC_TEA - System internal: machine data, NCK global- _N_NC_CEC - System internal: 'cross error compensation'- _N_NC_PRO - System internal: protection zones, NCK global- _N_NC_GD1 - User: 1st GUD block defined by _N_SGUD_DEF, NCK global- _N_NC_GD2 - User: 2nd GUD block defined by _N_MGUD_DEF, NCK global- _N_NC_GD3 - User: 3rd GUD block defined by _N_UGUD_DEF, NCK global- _N_NC_GD4 - User: 4th GUD block defined by _N_GUD4_DEF, NCK global- _N_NC_GD5 - User: 5th GUD block defined by _N_GUD5_DEF, NCK global- _N_NC_GD6 - User: 6th GUD block defined by _N_GUD6_DEF, NCK global- _N_NC_GD7 - User: 7th GUD block defined by _N_GUD7_DEF, NCK global- _N_NC_GD8 - User: 8th GUD block defined by _N_GUD8_DEF, NCK global- _N_NC_GD9 - User: 9th GUD block defined by _N_GUD9_DEF, NCK global- _N_NC_MAC - User: Macro definitions- _N_NC_FUN - User: Cycle programs- _N_CHc_OPT - System internal: option data, channel-specific- _N_CHc_SEA - System internal: setting data, channel-specific- _N_CHc_TEA - System internal: machine data, channel-specific- _N_CHc_PRO - System internal: protection zones, channel-specific- _N_CHc_UFR - System internal: frames, channel-specific- _N_CHc_RPA - System internal: arithmetic parameters, channel-specific- _N_CHc_GD1 - User: 1st GUD block defined by _N_SGUD_DEF, channel-specific- _N_CHc_GD2 - User: 2nd GUD block defined by _N_MGUD_DEF, channel-specific- _N_CHc_GD3 - User: 3rd GUD block defined by _N_UGUD_DEF, channel-specific- _N_CHc_GD4 - User: 4th GUD block defined by _N_GUD4_DEF, channel-specific- _N_CHc_GD5 - User: 5th GUD block defined by _N_GUD5_DEF, channel-specific- _N_CHc_GD6 - User: 6th GUD block defined by _N_GUD6_DEF, channel-specific- _N_CHc_GD7 - User: 7th GUD block defined by _N_GUD7_DEF, channel-specific- _N_CHc_GD8 - User: 8th GUD block defined by _N_GUD8_DEF, channel-specific- _N_CHc_GD9 - User: 9th GUD block defined by _N_GUD9_DEF, channel-specific- _N_AXa_OPT - System internal: option data, axial- _N_AXa_SEA - System internal: setting data, axial- _N_AXa_TEA - System internal: machine data, axial- _N_AXa_EEC - System internal: leadscrew error compensation data, axial- _N_AXa_QEC - System internal: quadrant error compensation data, axial- _N_TOt_TOC - System internal: toolholder data, TOA-specific- _N_TOt_TOA - System internal: tool data, TOA-specific- _N_TOt_TMA - System internal: magazine data, TOA-specific- _N_NC_KIN - System internal: data to describe kinematic chains, NCK-specific- _N_NC_NPA - System internal: data to describe 3D protection zones, NCK-specific- _N_NC_WAL - System internal: data to describe coordinate-specific working area limitationc = Channel number