Panasonic TX-40C320E Operating Instructions Manual

Panasonic TX-40C320E Operating Instructions Manual Manual pdf 11 page image

English - 11 -Switching On/OffTo Switch the TV OnConnect the power cord to a power source such as awall socket (220-240V AC, 50 Hz).To switch on the TV from standby mode either:• Press the Standby button, Programme +/- or anumeric button on the remote control.• Press the side function switch on the TV until the TVcomes on from standby.To Switch the TV OffPress the Standby button on the remote control orpress the side function switch on the TV until the TVswitches into standby mode.To power down the TV completely, unplug thepower cord from the mains socket.Note: When the TV is switched into standby mode, thestandby LED can blink to indicate that features such asStandby Search, Over Air Download or Timer is active. TheLED can also blink when you switch on the TV from standbymode.First Time InstallationWhen turned on for the first time, the languageselection screen is displayed. Select the desiredlanguage and press OK.On the next screen, set your preferences using thedirectional buttons.Note: Depending on the Country selection you may be askedto set and confirm a PIN at this point. The selected PIN cannotbe 0000. You have to enter it if you are asked to enter a PINfor any menu operation later.About Selecting Broadcast TypeAerial: If Aerial broadcast search option is turned on,the TV will search for digital terrestrial broadcasts afterother initial settings are completed.Cable: If Cable broadcast search option is turned on,the TV will search for digital cable broadcasts afterother initial settings are completed. According to yourother preferences a confirmation message may bedisplayed before starting to search. Select YES andpress OK to proceed. To cancel operation, select NOand press OK. You can select Network or set valuessuch as Frequency, Network ID and Search Step.When finished, press OK button.Note: Searching duration will change depending on theselected Search Step.Analogue: If Analogue broadcast search option isturned on, the TV will search for analogue broadcastsafter other initial settings are completed.Additionally you can set a broadcast type as yourfavourite one. Priority will be given to the selectedbroadcast type during the search process and thechannels of it will be listed on the top of the ChannelList. When finished, press OK to continue.You can activate Store Mode option at this point.This option will configure your TV’s settings for storeenvironment. This option is intended only for store use.It is recommended to select Home Mode for homeuse. This option will be available in Setup>More menuand can be turned off/on later.Press OK button on the remote control to continueand the Network/Internet Settings menu will bedisplayed. Please refer to Connectivity section toconfigure a wired or a wireless connection. After thesettings are completed press OK button to continue.To skip to the next step without doing anything pressthe Rapid advance button on the remote.After the initial settings are completed TV will startto search for available broadcasts of the selectedbroadcast types.After all the available stations are stored, scan resultswill be displayed. Press OK to continue. The EditChannel List menu will be displayed next. You canedit the channel list according to your preferences orpress the Menu button to quit and watch TV.While the search continues a message may appear,asking whether you want to sort channels accordingto the LCN(*). Select Yes and press OK to confirm.(*) LCN is the Logical Channel Number system that organizesavailable broadcasts in accordance with a recognizablechannel number sequence (if available).Note: Do not turn off the TV while initializing first timeinstallation. Note that, some options may not be availabledepending on the country selection.Media Playback via USB InputYou can connect 2.5” and 3.5” inch (hdd with external powersupply) external hard disk drives or USB memory stick to yourTV by using the USB inputs of the TV.IMPORTANT! Back up the files on your storage devicesbefore connecting them to the TV. Manufacturer willnot be responsible for any file damage or data loss.Certain types of USB devices (e.g. MP3 Players)or USB hard disk drives/memory sticks may not becompatible with this TV. The TV supports FAT32 andNTFS disk formatting.While formatting USB hard drives which havemore than 1TB (Tera Byte) storage space you mayexperience some problems in the formatting process.Wait a little while before each plugging and unpluggingas the player may still be reading files. Failure to doso may cause physical damage to the USB playerand the USB device itself. Do not pull out your drivewhile playing a file.You can use USB hubs with your TV’s USB inputs.External power supplied USB hubs are recommendedin such a case.It is recommended to use the TV’s USB input(s)directly, if you are going to connect a USB hard disk.