Panasonic CT-35S31S Operating Instructions Manual

Panasonic CT-35S31S Operating Instructions Manual Manual pdf 43 page image

Programming The Universal Remote ControlVCR Cable Converter BoxPreferred Procedure - Code Known Preferred Procedure - Code KnownProgramming Universal Remote Using Infra-Red Access Programming Universal Remote Using Infra-Red Access CodesCodes for VCRs for Cable Television Converter BoxesDetermine brand of VCR.Identify code(s) associated with the brand in the infra-red codeindex for VCRs (located in this manual).Determine brand of Cable Television Converter box.Identify code(s) associated with the brand in the infra-red codeindex for Cable Television Converter boxes (located in this manual).Procedure1. Place the Remote TV/VCR/CABLE switch into the VCR position(Center). TVfVCPJCABLEProcedure1. Place the Remote TVNCR/CABLE switch into the CABLEposition (Right) TWVCPJCABLEr-N2. Press and hold VCR POWER button down on - UniversalRemote. VCRPOWER2. Press and hold the CABLE POWER button down on UniversalRemote. CABLEPOWER3. Enter two digit code using keyboard "0 through 9" buttons.Release VCR Power button. The Universal Remote is nowprogrammed.3. Enter two digit code using keyboard "0 through 9" buttons.Release VCR Power button. The Universal Remote is nowprogrammed. Use the Remote VCR CHANNEL UP/DOWNbuttons for selecting Cable Converter Box channels,NOTE: Some brands have multiple codes. Repeat procedureusing each code listed until VCR responds correctly.Alternate Procedure - Code UnknownProgramming Universal Remote Using the "Sequence Method"for VCRsConfirm VCR is plugged in and operating properly, then turn OFF.Procedure1. Place the Remote TV/VCR/CABLE switch into the VCR position(Center).2. Press and hold the VCR POWER button down on UniversalRemote.3. Press VOL RIGHT button repeatedly. Check for the VCR to turnON after each press. When the VCR turns ON, release VCRPower button. The proper infra-red code has now been accessed.NOTE: Some brands have multiple codes. Repeat procedureusing each code listed untilCable Television Converterbox responds correctly.Alternate Procedure - Code UnknownProgramming Universal Remote Using the "Sequence Method"for Cable Television Converter BoxesConfirm Cable Television Converter box is plugged in and operatingproperly, then turn OFF.Procedure1. Place the Remote TVNCR/CABLE switch into the CABLEposition (Right).2. Press and hold the CABLE POWER button down on UniversalRemote.3. Press VOL RIGHT button repeatedly. Check for the CableTelevision Converter box to turn ON after each press. When theCable Television Converter box turns ON, release Cable Powerbutton. The proper infra-red code has now been accessed.NOTE: It may take several attempts before the correct code isfound.The VOL LEFT button can be used to return to a codethat was accidently passed by.Some Remote Controls may have unique operatingfunctions for some buttons. For Example: The POWERbutton may only turn the VCR OFF as opposed to bothON and OFF. It will then be necessary to modify theprocedure. Turn the VCR ON and repeatedly press theVOL RIGHT button until the VCR turns OFF.NOTE: It may take several attempts before the correct code isfound.The VOL LEFT button can be used to return to a codethat was accidently passed by.Some Remote Controls may have unique operatingfunctions for some buttons. For Example: The POWERbutton may only turn the Cable Television Converterbox OFF as opposed to both ON and OFF. It will thenbe necessary to modify the procedure. Turn the CableTelevision Converter box ON and repeatedly press theVOL RIGHT button until the Cable Television Converterbox turns OFF.!NOTE: When operating equipment (VCR or Cable Converter box) with the Universal Remote Control, the TVNCR/CABLE Switch Jshould be set to the same position where the Access Code was first programmed for the equipment. Otherwise, leave the switch!in the "IV position.-43-